like by playing with the different sizes of bricks or check mechanical properties by using a different type of mortar. Is there any software in which I perform such a type of analysis?
Dear Anees,
ABAQUS is a powerful finite element software which is used widely to simulate masonry units.
Like Mohammad Reza Pashaie , I also use ABAQUS for numerical modeling of masonry and it has served me very well.
I seed my cell (KG1a )in opti-mem media for transfection (without lipofectamine as control ) and after 2 hours I add FBS 10 ul in each wells all my cells after 24h in control wells or with...
07 July 2024 407 0 View
Kg1a cell line in 96 well plates do you think this white dots are contaminations or depris ( insides black circle)
29 June 2024 5,154 1 View
My Kg1a cell lines grow very well in flask, but when I seed it in 96 wells plate give only 25 % viability
24 June 2024 4,596 3 View
Recently, I have been trying to quantify the expression of miRNA. I have extracted the miRNA. However, I am not clear about using the cDNA synthesis kit usually there are two kits providing by...
16 June 2024 9,723 2 View
I need to get the previous example codes of silvaco to understand the basic mathematical modelling , meshing and doping of the AlGaN/GaN HEMT
20 May 2024 233 0 View
when Mg substituted in Ni Zn ferrites crystalline size increase but lattice constant decrease in soft ferrites xrd
24 October 2023 7,485 5 View
in Mg substituted Ni Zn ferrites ho Mg effects its structural properties ,dielectric properties, electrical properties .uv spectroscopy
23 October 2023 874 0 View
crystalline increase as Mg concentration increase
22 October 2023 8,946 0 View
both have same graph at low and hihg frequenc
21 October 2023 8,802 2 View
working principle of uv
21 October 2023 4,348 0 View
I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...
07 August 2024 5,177 3 View
I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...
02 August 2024 2,890 0 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.
25 July 2024 9,976 3 View
I am using gelatin to model mechanical properties of brain tissues in-vitro. Do you have any suggested concentration ? Thank you so much.
19 July 2024 3,095 0 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
..
10 July 2024 3,444 4 View
The diagram suggests that there is a contradiction within the second law of thermodynamics and Carnot's efficiency theory. According to the second law, Carnot efficiency is independent of the...
08 July 2024 7,478 4 View
For the PDMS material, it's linear thermal expansion coefficient is about 3.2*10-4/℃. The polyimide has a smaller linear thermal expansion coefficient like 2*10-5/℃, but it cannot be stretch. It...
04 July 2024 4,525 1 View