How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View