11 November 2018 0 4K Report

I look for a correct correlation between the surrogate safety measures defined by T-Analyst and the parameters of SSAM in terms of pedestrian safety

More Tiziana Campisi's questions See All
Do you have experience about Pedestrian trajectories with Viswalk?

Dear all I need of your help about the definition of Pedestrian trajectories on VISWALK. I obtained from simulation the trj file but is not possible to use or compare with other trajectories...

11 December 2018 9,331 3 View

Does Viswalk trajectories link to SSAM tool?

Good evening I can start to study Viswalk trajectories considering only pedestrian flow. I need to know if it is possible to study pedestrian safety and obtain surrogate safety measures using...

11 December 2018 8,866 0 View

Do you have experience about Pedestrian trajectories with Viswalk?

Dear all I need of your help about the definition of Pedestrian trajectories on VISWALK. I obtained from simulation the trj file but is not possible to use or compare with other trajectories...

11 December 2018 9,205 0 View

Can you suggest me journals about Transportation system ISI indexing with impact factor?

I need of more details about International journals focused on Transportation topic with ISI indexing and Impact factor

31 December 2017 6,551 0 View

Enviromental aspect related ramp meterig:did you ever experiences about this focus?

I need to collect more details and experiences related to the study of environmental aspect related to ramp metering.

02 March 2016 4,083 0 View

Similar questions and discussions
Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)*S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)*S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View

What is the ideal value of UACI for image encryption scheme?

UACI - Unified Averaged Changed Intensity between cipher images. Why some papers refer ideal value to be 33.33 and some refer it to be 33.46? Which is the correct value? (In reference to image...

11 February 2021 9,562 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close