Is mwcnt or swcnt more suitable for electronic devices applications?

04 April 2015 1 2K Report

There are confusion of comparative dispersibility of MWCNT in Ethanol and Acetone for their separation and also for their compatibility for nanostructured devices like FET, junction diode.

Uppari Venkataramudu

CNTs can be formed as single-walled nanotubes (SWCNTs) which are either semiconducting or metallic depending on their chirality and multi-walled nanotubes (MWCNTs) which are metallic. For FET devices, requires separating the metallic CNTs out of the mix with SWCNTs

So, swcnt more suitable for electronic devices applications.

Badges
Science topic

More Priyanka Nehla's questions See All

How MWCNT/SWCNT can be converted from metallic to semiconducting or insulating and vice versa ?

how the carbon nano tube's conducting property changes in certain enviornment? are these properties temperature dependent only or any else factor dependent?

03 April 2015 3,025 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View