Is it possible to do Reitveld Refinement on single crystal XRD data?

I tried to do single-crystal Rietveld Refinement on my single-crystal XRD data using the option "refinement on single-crystal data/ integrated intensity data" in Fullprof but it is giving error...

30 January 2021 7,813 3 View

What will be the impact on Antenna performance to shift the resonant frequency by RLC Matching network?

There is always a possibility to shift the resonance frequency by adding a RLC matching network. I wonder what will be the consequence on antenna performance (axial ratio, gain)? If there is no...

13 September 2020 5,187 3 View

Axial ratio shows different result at different ortogonal setup. What could be the reason ?

17 June 2020 5,332 3 View

Firm survival and mortality: How to relate both?

I have two data sets 1. Age of all the surviving firms at any given point of time. The age distribution is an exponential function 2. The age of all the firms which died at a given point of time (...

01 February 2020 3,542 1 View

Why Antenna shows negative gain even though it has very good matching?

I am aware of the fact that electrically small antennas are poor radiators with very small gain and low efficiency. One main cause of this is poor matching. An extremly electrically small antenna...

19 January 2020 5,285 9 View

What is the impact of image current from ground plane on patch antenna? I wonder how it radiates if ground plane is very near to radiator?

As we know, patch antenna is combination of two magnetic dipole. If we place a perfect electrical conductor near a dipole, antenna performance will suffer significantly. Then how a patch antenna...

27 November 2019 7,597 5 View

I am getting two peaks at 702 and 705 eV for Fe 2p scan of a composite made from Fe-salen.how it can be explained?

the pure Fe-salen spectra is in conformity with literature,but the composite is showing two extra peaks at 702 and 705 eV. Can anybody explain about why the peaks are coming.

23 July 2019 5,710 3 View

What will be the cororidinate(theta and phi) to evaluate the axial ratio?

I have designed a circular polarized antenna. But , I am confused with cor-ordinate system. In some angel it shows less than 2 dB axial ratio and some other point it shows more than 10 dB like a...

23 May 2019 2,175 7 View

Why there is a big difference in between realize gain and gain in my design?

I have designed a multiport antenna. Where as, I have 2 dB Gain but realize gain is -6 dB. Point to be noted, S11 is really good. I have -25 dB return loss at my desired frequency.

22 November 2018 6,165 17 View

Bands in western blot are behaving like GHOST!!!!!!!!!!!!!!!!!?

I am doing western blot and after development I can see that one/ two lanes have no band. Perhaps, next day I am doing same gel run with same sample with no change in protocol, this time another...

25 September 2018 8,325 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View