Change of node co-ordinates before and after the deformation in ANSYS workbench ?

Can anyone tell 1) How to identify the node co-ordinates before and after deformation in ANSYS workbench? 2) How to identify the nodal displacement, as ANSYS provides only deformation values ?

08 September 2016 9,248 3 View

Node to Node Connectivity in ANSYS ?

Can anyone please help to provide information to provide node to node connectivity on the highlighted portion. I am working on ANSYS 15.0 and unable to getting the node to node connnectivity.

06 July 2016 4,019 8 View

How to calculate the range of motion for lumbar vertebrae L1-L3. What is the boundary condition we should consider in ANSYS for getting the ROM?

We have to calculate the range of motion. Please share the procedure, how to do this ?

04 May 2016 846 2 View

Quad mesh for Vertebrae ? MESHING In ANSYS 15.0 ?

Hello All, I am trying to mesh L2 vertebrae as hex dominant Quad mesh but due to its complex geometry, unable to do the same. Vertebrae is generated by CT images and having patches on all over the...

01 February 2016 6,968 4 View

Center of Rotation for L2-L3-L4?

01 January 1970 9,410 0 View

Buffer Exchange using column packed with sephadex G-25 effect on protein concentration?

Hello, If i am doing a buffer exchange for an antibody of 1mg/mL, does the elution lose protein in the process of buffer exchange? For example, if i flow through 500 uL of 1mg/mL sample, and...

03 March 2021 6,299 3 View

No title

03 March 2021 5,360 2 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

No amplification data for qPCR on MxPro?

I have set up a qPCR run on MxPro with SYBR green and ROX as a reference, however, when I go to the analysis section the program seems to only collect data for the dissociation curves and not the...

25 February 2021 8,039 1 View

Can I use TCA instead of TFA for protein analyis in RP-HPLC?

I am trying to analyze lipase using the reverse phase-HPLC C18 column. In the literature, 0.1 % TFA was and 60% ACN was used. Can I use TCA in place of TFA? If any other methods are available to...

25 February 2021 2,388 3 View

Can I use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography?

Hi! I would want to know if I can use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography. This column has a polyethylene glycol phase, but I can't find the manual to check...

22 February 2021 730 2 View

My silica gel column dried can I somehoe save the trapped matter?

I tried to separate my substance from a protein in a sillica gel column. By mistake, it dried and cracked. Can I save the trapped substance? Can I repack it ,or at least elute all of the trapped...

22 February 2021 1,789 3 View