In what cases the ionic drop is crucial (to affect the measurements) during a regular corrosion testing.
The nonmetallic inclusions are problematic particles that develop during the steel making process. They are tiny entities that exist in high numbers. They disrupt the mechanical homogeneity of the...
31 December 2014 7,761 16 View
There are a few points being raised lately on the first direct evidence on the universe inflation and the detection of gravitational waves: 1. The cosmic microwave polarization patterns referred...
04 May 2014 4,140 3 View
The egg is one of the unique feats of natural engineering. Its three-dimensional arch structure can support the weight of a standing human being yet it is so delicate that a baby bird can peck its...
03 April 2014 4,654 4 View
This question is open for chemists, metallurgists, physicists and astrophysicists: Check out this diagram which has been released today on Universe inflation. It describes how the universe has...
03 April 2014 329 22 View
In case for example the status 'With Editor' did not change for two months or so, Are there risks of any kind the corresponding author should be aware of when reaching the journal's editorial...
02 March 2014 7,100 2 View
Please see attached this figure from a journal paper I am currently reviewing. I made slight changes to it to maintain the anonymity. The paper addresses the significance of H2S with the...
02 March 2014 6,537 1 View
Please check out these potentiodynamic profiles for experiments I recently carried out: it shows potentiodynamic scans for a pipeline steel immersed in CO2-saturated solutions of different...
02 March 2014 3,069 13 View
I am currently reviewing a research paper presenting an electrochemical study on corrosion-enhanced erosion. It attempts to link the CFD of a modeled flow to the corrosion rates of an elbow made...
02 March 2014 4,297 5 View
Please check out this question excerpted from a standardized test for high-school students in a North American country; It says: Which of the following would be a graph of speed vs. time for the...
02 March 2014 8,400 3 View
To test the corrosion behavior (or resistance) of an engineering material in an aqueous medium one can carry out immersion tests for specific periods of time across which the mass loss and...
02 March 2014 4,690 11 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...
30 July 2024 6,420 1 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...
27 July 2024 5,748 0 View
Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...
25 July 2024 8,108 0 View
It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...
25 July 2024 8,738 0 View
In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...
25 July 2024 7,982 3 View
Dear all, I gave 116 respondents 18 translated sentences and asked them to indicate their levels of acceptance of these translations on a five-point scale. Some translations result from strategies...
24 July 2024 8,245 5 View
I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...
23 July 2024 9,938 1 View
I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?
23 July 2024 5,776 2 View