If the value of gap capacitance in minus, what does it mean?

Mowafak K. Mohsen @Mowafak_Mohsen

02 February 2019 1 2K Report

I have gap capacitance between two patches and i get minus value its that correct if yes what is that mean?

Ahmed Musa Dinar

Dear Mowafak, I think the answer of your quastion in this link

https://www.researchgate.net/post/What_is_negative_capacitance

Badges
Science topic

Similar topics
Correction

More Mowafak K. Mohsen's questions See All

What is the different between review paper and survey paper?

i have to write literature review about my work what is the different between review paper and survey paper .

08 September 2018 3,791 0 View

I already upload my article in research gate but i didn't find it in my google scholar. why?

how to make connection between research gate and google scholar

06 July 2018 9,559 0 View

Can i get graph of attenuation constant vs frequency from CST?

i already design microstrip antenna i want to get attenuation constant vs frequency

01 January 1970 1,813 0 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

How to find the capacitive response frequency from the impedance plot?

I have done electrochemical impedance by using cyclic voltammetry for one organic material. from that, I plotted bode diagram. but actually, I am very confused about how to find the capacitive...

18 February 2021 3,023 3 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View