I would like to know about the available theories of “impact failure”?

19 July 2020 0 9K Report

I have estimated the time-dependent impact forces of two colliding bodies (objects) with given curvatures. How can I estimate the lifetime of these bodies to prevent the failure?

Badges
Science topic

Similar topics
Force

More Reza Teymoori Faal's questions See All

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How to solve the fatal error "the entire source was rejected" in MCNP?

Simple geometry was made having concentric cylinders bounded by a square region. The geometry has a reflective boundary. The source was defined at one point in the boundary and when it had been...

17 February 2021 4,364 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

How to model Type 1 collagen structure for finite element analysis ?

I have started a project in which stress distribution in Type 1-collagen scaffold is to be modelled. I am thinking of using finite element analysis to model the structure and the loading...

07 February 2021 5,487 3 View

Hey guys, I'm looking for an efficient protocol to transfect patient-derived tumor cells with a high rate of transient transfection?

As you know it's quite tricky to get primary cells transfected at a relatively high rate!

31 January 2021 3,580 4 View

How can I model a vacuum region between a concentric tube in Ansys fluent?

I am modeling a double pipe (concentric tube) in Ansys Fluent. The center tube contains nanofluid, and the region between the pipes is a vacuum zone. The outer tube is used for reducing convection...

22 January 2021 2,781 3 View

What type of plants is better to work in gene regulation control project ?

I Interested in to work in gene network modeling thus I need to know what is future of gene network modeling in agriculture thanks

04 January 2021 6,527 3 View

Is it possible to culture several cell lines in the same plate/dish/flask with complete cell separation?

I'm trying to screen the effect of a toxic agent. I need to see its effect on a few different cell lines with different degrees of resistance to this compound. I would like to possibly culture...

31 December 2020 5,740 3 View

Help with insect identification?

Could someone help me identify the insect in this picture?

31 December 2020 2,109 5 View

How to find the natural frequency of nonlinear model (hyperelastic materials) in ansys APDL?

I'm working on the FE analysis of nonlinear vibration of circular plate in ansys APDL. I considered the Mooney-Rivlin model of hyperelastic materials. So i want to know that how to find natural...

27 December 2020 8,696 2 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

How can misfit between business requirents and ERP system business process be reduced?

One main reason for failure of most ERP implementations is the misfit between business requirents and ERP system business process be reduced. How can the misfit between business requirents and ERP...

22 February 2021 5,709 5 View

How to include additional force field in GROMACS?

I have a cellulose model system that is best described by the GLYCAM06 force field according to the literature. However, the set of force fields included in the GROMACS package doesn't include the...

20 February 2021 3,309 3 View

How to perform Kaplan-meier survival analysis in SPSS?

Hi everyone, This is my first time of attempting to run survival analysis. I have a data on patients with End-stage Kidney Diseases (ESKD). I would want to run survival probability by treatment...

16 February 2021 2,647 3 View

I want to simulate a system containing protein and heavy metals; which force field is most reliable for this purpose?

The protein I want to simulate has multiple heavy metals. I wanted to know which force-field I should use with GROMACS to achieve this. Most importantly, do the latest updates in the force-field...

16 February 2021 2,420 1 View

How to obtain parameters to run a simulation for benzene using CHARMM forcefield in GROMACS?

I have been reading this paper Soft Matter, 2017, 13, 1904 and in this paper, they simulate benzene in GROMACS using CHARMM. They mention that they performed simulations of benzene using the...

15 February 2021 5,561 3 View

Gromacs force field and water model recommended for protein hydrophobic study?

Dear All, I received a comment from reviewer about asking me selection of force field and water model. I choose OPLS-AAL and 3-point water model. They mentioned the combination of OPLS-AAL and SPC...

13 February 2021 1,364 3 View

Hello .Ineed a researchs about systolic heart failure any one can help me ?

Am a master student .I need an information about this case to write my thesis?

09 February 2021 9,706 2 View