How to do buckling analysis in ansys apdl for laminated plate with PZT 5H attached?

I am doing buckling analysis of laminated plate surface bounded with two piezoelectric PZT 5H and axial compressive load is applied. I am getting an error, No ANEL table exists for material 2....

16 February 2021 510 1 View

Which furnace or method are suitable for direct melting of the powder ?

My question is very specific about melting of pure reduced Iron Fe in powder form

29 December 2020 4,352 3 View

I have one question related to cross correlation and auto correlation in neural network training?

Autocorrelation value is 0.3 and input cross-correlation error value is 3.Are the obtained results after training ANN is correct or wrong?

04 October 2020 9,686 2 View

Poly ICLC or Poly IC structure for docking ?

I want to do docking of Poly ICLC with protein. But, unfortunately there is no crystal structure for Poly ICLC or poly IC. Poly ICLC is a complex of Poly IC, poly lysine, and...

24 September 2020 6,107 1 View

What is the best way to preserve fungal RNA in shipping (1 - 2 days)?

The sample (fungal RNA) extracted with RNeasy Kit is supposed to be sent for sequencing.

15 September 2020 7,128 3 View

How to measure the T1 and T2 value from a MR image ?

I have an MR Dicom file having values of repetition time, echo time, Inversion time, flip angle, etc. I want to calculate T1 and T2 from this Dicom file. Is there any way to calculate this from...

12 March 2020 7,598 12 View

How to calculate LOD & LOQ in the validation of analytical method using HPLC?

I have injected 5 samples of lowest possible concentrations. I have taken the std deviation of area and slope of the equation obtained for the regression line of calibration to calculate LOD &...

19 January 2020 4,730 7 View

How to know the depth of Xylem in live plants and trees? Is there any tool in market?

Hi, I am looking for a tool to measure the start and end of xylem tissue in plant and tree. Please send the link if such product (s) are available commercially. Thank you

18 January 2020 8,808 0 View

How do I get a charge discharge curve in a potential window similar to that of potential window of CV in Autolab workstation with nova software 2.1.4?

03 January 2020 1,399 2 View

I am trying to evaluate the efficacy of Iron and gold nanoparticles for photothermal therapy using laser irradiation ?

I am trying to check the performance (efficiency of nanoparticles for heat generation) of green synthesized Iron oxide, Gold nanoparticles and their composite for photo-thermal therapy. I have...

26 June 2019 8,874 5 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View