I want to simulate a linear motor in matlab, but I don't know how - can anyone help?

Mehdi Hedayatpour @Mehdi_Hedayatpour2

10 October 2013 1 9K Report

Linear motor.

Mohamad Amin Bakhshali

You can find some useful MATLAB code in these link:

http://www.mathworks.com/matlabcentral/newsreader/view_thread/265208

http://www.mathworks.com/help/control/getstart/linear-lti-models.html

Badges
Science topic

More Mehdi Hedayatpour's questions See All

Is there a microgrid with inductive line impedance (X>>R)?

hello I have work on microgrid area and microgrid voltage and frequency control. there is a contradiction for me about selecting the line impedance type (R>>X or X

10 November 2015 764 14 View

How can I determine input of fuzzy logic power system stabilizer?

Hello dear friends I work on power system stability. I have designed a power system stabilizer using fuzzy logic for damping of low frequency oscillation. Because it is difficult to directly...

31 December 2014 6,363 3 View

What are the best countries given the current state of the world, in fields of economics and culture?

What is your opinion in relation to best countries for life, education, jobs, income etc

02 March 2014 9,986 5 View

what are the drawbacks of voltage controlled of D-statcom?

As you know probably, conventional control method of D-statcom is based on the voltage control. In non-linear loads condition, what are the drawbacks of this method?

01 February 2014 6,787 1 View

How can I see outputs in STATCOM?

I want to simulink a STATCOM in the transmission line, but I can't see the STATCOM outputs. How can I see the output signals in scope? When I run this M.file (see attached) it gives me an error....

01 February 2014 7,529 4 View

How can I see Simulink output vector of STATCOM in matlab simulink?

I want use a STATCOM in Transmission line but I can't see the output of STATCOM in simulink. I would like to know how can I create an output block for STATCOM.

01 February 2014 9,404 3 View

How can I see STATCOM outputs?

In this picture, where can I find the signals & scope block in MATlab simulink? I looking for this block for depict of STATCOM outputs.

01 February 2014 224 2 View

How can I perform a dynamic simulation of BLDC motors in matlab simulink?

Your assistance is appreciated.

31 December 2013 6,318 5 View

How can I perform a dynamic simulation of BLDC motors in matlab simulink?

Dynamic simulation of BLDC motors in matlab simulink.

31 December 2013 3,257 6 View

Can anyone advise on designing a hybrid apf model using Matlab simulink?

Seeking an advice.

31 December 2013 1,642 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View