I want to calculate average of a graph?

More Shah Fahad's questions See All

Can reactive power control alone keep voltage output of DG balanced ?

Dear Researchers, To my knowledge, output voltage and reactive power in droop control dependent on each other. If I am using multiple grid connected Distributed Generators (DG's) and through any...

02 March 2019 3,149 11 View

Any latest Phd topics for renewable energy control (Solar or wind)?

I am going to write a proposal for my Phd. I have been studying some research papers and i have developed some ideas. But i want to make sure that i have gone through all the choices. Kindly...

31 December 2017 6,009 11 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

What are some signs that an ECM is overfitting the Nyquist plot?

What can you look for to know that the circuit model being used is overfitting the data. How do you know when overfitting is occurring?

31 July 2024 7,425 0 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

There is possible way to calculate experimental DOS from the UPS spectrum of the material. How to calculate the DOS from UPS?

Here, I have attached the UPS graph. I'm trying to calculate the DOS/DOVS from the UPS.

29 July 2024 4,971 1 View

Can i apply a public questionnaire but analyse it with a different data analysis method?

First, thanks for taking the time to read my puzzle 🥹! I am currently working on the methodology part of my dissertation, and I have chosen a questionnaire as the instrument for my quantitative...

27 July 2024 3,457 3 View

How to merge two or more linkage maps?

I have three linkage maps that needs to be integrated to create a consensus map for QTL mapping.

25 July 2024 6,505 2 View

Critique Calculaltion in Topological Indices and QSPR Modeling?

The first step is to analyze a 2D molecular graph and implement partitioning techniques to calculate the topological indices. Secondly impose statically tools to generate QSPR model, may or may...

24 July 2024 9,644 1 View

How to do calculation of Louvain methods calculation for excel sheet and and is there any software available?

The Louvain method – named after the University of Louvain where Blondel et al. developed the algorithm – finds communities by optimizing modularity locally for every node’s neighborhood, then...

23 July 2024 6,659 0 View

Swerling Characteristic functions?

Hello!!! I want to implement the Swerling characteristics functions (CF) directly in MATLAB without using its Fourier integral pairs...the Swerling CFs are actually Laplace Transform of the signal...

23 July 2024 4,925 1 View

Mohammad Soroosh

I suggest that you present a sample of graphs. At this time, integration of graph on a defined interval can help to solve this problem.

Shah Fahad

Integration through code ? Or there is any simulink block for it ?

Mohammad Issa Sowaity

I suggest you to study the energy of the graph. Also, you can study a lot of types in the energy of the graph, for more you can see

Article Laplacian Sum-Eccentricity Energy of a Graph

and

Article The Sum-Eccentricity Energy Of A Graph

Regards.