I did DSC calorimetry of solid sample. dsc endo up. But another up peak is observed before melting peak(at correct melting point) why two up peaks ?

07 July 2018 1 7K Report

What is the phenomenon behind the peak at 410K?Please help me

Badges
Science topic

Similar topics
Correction

More Aboothahir Afzal's questions See All

Which is the peak corresponding to glass transition temperature in the DSC graph endo up?

In the attached file is dsc of my sample. I have numbered the peaks seen inthe graph. I am seeing three peaks endothermic other than melting. so can u u identify which one is glass transition peak

02 March 2019 6,886 5 View

Which is the peak corresponding to glass transition temperature in the DSC graph endo up?

out of the endothermic peaks which is the glass transition temperature

02 March 2019 6,975 9 View

I did DSC calorimetry of solid sample. dsc endo up. But another up peak is observed before melting peak(at correct melting point) why two up peaks ?

irn the figure given actual melting point is 423k but I am getting melting peak in this temperature aswell as a peak lower than this temperature..what phenomenon does the up peak below melting point

06 July 2018 8,744 1 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How can I find a Raman spectrum wavenumber corresponding to what compound?

I have several Raman spectra with very distinct peaks at certain wavenumbers, such as 277, 359, 466, 583, 623, 686, and 795cm-1. How can I identify them to what compound(s)? The RRUFF and others...

24 February 2021 363 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

Genescan gives 3 peaks instead of one?

Hi all, I am doing a genescan analysis for a deleted exon in the patient sample. The amplified region is 215 bp. In the patient sample because of homozygous deletion, no peak is observed while in...

23 February 2021 5,645 1 View