Is it possible to report hydrodynamic loads on different parts of an ocean vehicle while 6DOF motion analysis in Ansys Fluent is running?

It seems a 6dof UDF containing vehicle characteristics such as mass and moments of inertia can be used for specifying a boundary as reprentative of ocean vehicle. It is required to have...

03 February 2021 7,726 3 View

About nanocapsules: how can I interpret smaller nanoparticle size by enhancing the polymer amount used?

in most articles nanoparticle size decreases by lower amount of polymer

16 November 2020 4,669 6 View

Can anyone please provide information in regards to the utilization of the exoskeleton as a perturbative tool for gait/balance therapy?

There exists a considerable body of literature on the application of exoskeleton as an assistive tool in the area of gait or balance therapy. I am interested in finding out more about the...

06 October 2020 9,317 3 View

How to propagate the EMC Virus in L929 cell line?

04 October 2020 6,705 2 View

Is there anybody to share a RevMan tutorial file with me?

I am busy writing a meta-analysis manuscript. I had passed a RevMan course previously, however, I need to be refreshed again.

21 September 2020 3,535 5 View

Why would a negative control have apoptosis in the Annexin V-PI Flow Cytometry?

06 August 2020 3,627 22 View

What does "Mesh has uncovered edges" mean in ICEM CFD?

hello everyone, I need your help. I was meshing a porous media geometry with ICEM, and after meshing, I wanted to transfer the data to #fluent, I encountered this error "WARNING: Mesh has...

31 July 2020 3,695 3 View

How would i synthesize homogeneous nano-ferro fluid?

I want synthesize nano-ferro fluid by using of Fe2O3 or Fe3O4. Do you think i can forming this homogeneous fluid with this NPs or not? In during synthesize of NPs, should them distribute in...

23 June 2020 3,223 13 View

Some questions about DWT of an image in MATLAB?

Hello, every one 1) I load the "barbara" image in MATLAB using the following command: load woman It is saved in workspace as "X" and its matrix class is "double". Then, I define "Y" as...

18 June 2020 8,232 8 View

Do weak contribution equations within a module use the module's boundary condition in COMSOL?

I am trying to solve a partial wave equation for scattered quasi-TE waves. I found the COMSOL built-in Helmholtz equation module very close to my problem. The bottleneck was that, I couldn't...

03 June 2020 8,937 1 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

No title

25 February 2021 5,713 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View