How would you control the feed water flow rate into the drum of a waste heat boiler attached to a steel converter?

02 April 2019 0 9K Report

Rapid change in the heat input from the converter causes an immediate swelling of the water in the drum but also requires the flow rate to to increase rapidly.

Badges
Science topic

More John Borer's questions See All

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

What is the minimum number of studies in each category required for a multiple subgroup analysis to be viable in a meta-analysis?

Cochrane Handbook mentions subgroup analyses are only warranted if there are more than 10 studies (I have 28), and if they are distributed evenly among categories of subgroup. I am wondering if...

17 February 2021 3,467 4 View

How do you interpret multiple meta-regression in STATA?

Please could someone recommend a resource that explains performing meta-regression with multiple moderators. I have read the STATA META ANALYSIS REFERENCE MANUAL, but this only gives examples of...

17 February 2021 7,376 1 View

How many indicators do I need to represent a latent construct?

Hi folks! We did a large survey and planned to use 3 indicators to represent a latent construct (Sense of Place/SoP) in a latent regression model (structural equation modeling). However, one of...

15 February 2021 7,705 3 View

What is the structure of a photon that can describe the interference experiments that reject the wave nature of light?

De Broglie's double-solution postulated a causal model of Quantum Mechanics. Knowledge of the photon structure was needed to model the particle part of the cause of the Double Slit interference...

11 February 2021 6,869 5 View

How do you incorporate a study that used non-parametric analysis into a meta-analysis where majority of studies used parametric?

I am calculating Hedge's g for effect sizes, so I am pulling means, SDs, and Ns, from each study. However, one study did a Mann-Whitney U test, and so reports Mean Rank, Sum of Ranks, U, Z, and r...

31 January 2021 1,182 5 View

How to share a struct between client.c and server.c in Contiki RPL UDP ?

I'm trying to include udp-client.c in udp-server.c to share a struct between them But I keep getting this error udp-server.c:67:1: error: redefinition of autostart_processes In file included...

16 January 2021 5,013 4 View

Do you know any CEFR-annotated learner corpora for writing tasks?

Dear researchers, I have been working on a machine learning algorithm to classify language learners' writing tasks automatically according to the CEFR levels. The aim is to use...

03 January 2021 7,041 2 View

Who are the leading Indigenous academics who have researched and published on STEM teaching and learning?

I'm interested to read what leading Indigenous academics have to say about the intersection between traditional or Indigenous knowledges/epistemologies, values/axiologies and ways of...

14 December 2020 10,026 10 View

How to performe a non-inferiority test in an adjusted linear regression?

I am looking for the relation between weight evolution (continuous) and a binary factor adjusted for confounders. The regression gives an (adjusted) difference and its CI less than the planned a...

13 December 2020 8,061 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Is stone a sustainable material? Is it a sustainable approach to use natural stone waste in architecture?

I'm designing a zero-waste restaurant and considering using marble waste to make some tables and a bar countertop. My clients think it's not "sustainable enough" and I would like to have more...

01 March 2021 4,326 7 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View