how to use a single radio medium for scalar and dimensional in OMNeT++?

05 August 2021 0 3K Report

how can i use a single radio medium for scalar and dimensional transmission. i got suck in this check and cast error showing.can't cast scalar transmission to dimensional. please help

Badges
Science topic

Similar topics
Filing

More Annu Malik's questions See All

How to simulate elliptive curve cryptography in IoT using omnet++?

How to simulate elliptive curve cryptography in IoT using omnet++. any tool please suggest. I have installed NETA but it works on older version of INET and OMNET which does not support sensor...

06 February 2022 8,618 3 View

How to configure a node for two interfaces(802.11 and 802.15.4)?

i want to implement a network in which a single node can have two interface but uses one at a time : 1st for wifi 802.11 2nd for zigbee 802.15.4 is it possible to do so, please help

04 August 2021 8,569 3 View

Working on Cooja simulator?

There are very less resources available regarding cooja simulator...if any one knows the source please share

01 April 2021 274 3 View

Which is the best suitable simulator for IoT research work?

31 March 2021 9,782 15 View

How can i simulate zigbee in cooja simulator??

How to simulate zigbee in cooja?

22 January 2021 7,026 4 View

I want to implement cross interface on gateway for wifi and zigbee. How can i simulate it on cooja simulate?

How can i deploy gateway on network window of cooja . And how to dynamically schedule the wake-up behaviors of both WiFi and ZigBee with bounded delay for maximized energy efficiency of the...

22 January 2021 2,092 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Which distribution type should I use when calculating the average particle size from TEM image? and how to calculate the error ?

average particle size calculation from TEM

04 August 2024 2,921 1 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How to find experimental demonstrations are available on MEC research using OMNET?

I attempted to find a tutorial on YouTube but couldn't locate it. Could anyone guide me on how to view simulation results for Mobile Edge Computing using the OMNET++ simulator?

06 July 2024 6,229 0 View

What is the best method for modeling the transmission and reflection of an electromagnetic wave incident on a magnetic multilayer thin film?

Previously, I successfully modelled the transmission and reflection of electromagnetic waves incident on non-magnetic materials. Please refer to my publications for details: 1- A polynomial model...

05 July 2024 1,396 2 View

What are the modules needed in MEC research ?

To elaborate on my question: When implementing offloading techniques in mobile edge computing using simulators like OMNET++, how can I complete the experiment with results and visualizations? I...

03 July 2024 5,238 2 View

How to prepare polyaniline emeraldine salt ( PANI -ES) sample for Transmission electron microscope (TEM) analysis?

I need to do TEM analysis for my Polyaniline emeraldine salt form. May I know which solvent is appropriate for preparing TEM sample?

25 June 2024 9,086 3 View

What may cause whitish discolor of polycrystalline diamond surface, and cracks near edge?

I am preparing polycrystalline diamond (PCD) with tape casting. The powder is 8~12 um. After drying of tapes, I place several tapes in Ta cup without warm-pressing. Next, debinding is carried...

23 June 2024 7,758 2 View