How to configure a node for two interfaces(802.11 and 802.15.4)?

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to call both UMAT and UEL together in Abaqus?

I have a model with bulk material (matrix) and inclusions and cohesive interface elements between both. For the bulk material, I have implemented a UMAT and for the cohesive interface elements, I...

20 February 2021 1,286 2 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm??

Can someone please tell me how to get a desired temperature (say 700C at the bar concrete interface ) which is at a depth of 15mm from the exposed surface in Abaqus... i am performing a coupled...

10 February 2021 4,656 2 View

In Abaqus, is it possible to remove elements which are too complex for meshing from a sequence obtained by getByBoundingBox() ?

Hello everyone, I'm trying to mesh a structure with complex partitions using mesh controls. When doing it on the user interface I'm first selecting all cells. In the following, I have to accept...

03 February 2021 8,198 1 View

I am working with crack propagation along with delamination using ABAQUS. Wether crack will start from a delaminated portion (cohesive crack) by XFEM?

I am modelling a SENB Beam with an interface. The interface is modelled with cohesive elements to permit delamination. The carck in the continumm is taken care by the XFEM. My doubt is the crack...

19 January 2021 4,827 1 View

Can we use the single-elimination tournament method as the basis of an experiment design?

I want to conduct an experiment in the field of Human-Computer Interaction, where I test the perception of users about which image is better using different camera lenses. In the experiment, I...

18 January 2021 779 2 View

Why are nanobubbles typically negatively charged?

Nanobubbles of air in water tend to have a negative charge. Intuitively, one could think the water is not charged, air is not charged: why are nanobubbles charged? Looking closer, water has both...

14 January 2021 3,563 3 View

How to interface Semi conductor physics and Fluid flow physics in COMSOL?. What are the parameters to be considered while we interface them?

I am using a silicon nano wire in microfluidic channel to identify the some changes in parameters like voltage and current. but i am unable to interface them. the two physics run individually but...

10 January 2021 8,894 1 View

What is the best model to be use for site prioritization using GIS-MCA interface?

What model can be use to identify prority risk site using multicriteria analysis and GIS techniques

05 January 2021 9,626 3 View

Tadiwa Elisha Nyamasvisva

Yes it is possible.

BUT. As you rightly said can not be activated at the same time because ZigBee and WiFi channels both exist in the 2.4 GHz band, existing in the exact same frequency space. Operating a ZigBee network and a WiFi network on the same frequency will cause them to interfere with each other. Usually, the ZigBee network will be impacted more.

Mohammad Faisal

NS3??

Real environment ?

Annu Malik

@tadiwa thank you for reply...can u suggest any help or guidance for this for omnet++ simulator