24 February 2020 4 8K Report

I would like to simulate a bio-inspired optimization based Geocast routing for VANET using a clustering algorithm in ns3 or Omnet++ with SUMO. And , evaluate my approach with other existing approaches.

I need source code of any geocast based routing protocol for VANET (such as: Gytar or Rover ) or any other position routing protocol (GPSR, GPCR) using a clustering algorithm. furthermore, I need to integrate an optimization algorithm such as ANT with in the routing protocol to deal with the optimal path selection.

I look forward to hearing from you.

thanks in advance.

More Nadia Tassoult's questions See All
Why does kaleidoscope Marker miss Bands in the middle??

We had several times the problem after the transfer: you can detect the yellow 10 kDa Band, the blue 20 kDa Band, the pink 25 kDa Band but after only the pink 75 kDa Band. 15, 37 and 50 kDa are...

02 February 2021 4,936 3 View

What's difference between NH4+ and NH4+-N, NO2-and NO2-N, NO3- and NO3-N?

Hello, Upon writing my paper, I noticed that most journal papers stated the concentration of all nitrogen compounds in -N , example instead of NH4+ its NH4+-N. I knew that the -N form uses the...

14 December 2020 3,693 3 View

Where and how do I specify frequency in the route section of frequency-dependent calculation (Gaussian using Linux)?

Hello everyone. I would like to compute the dynamic hyperpolarizability value of a molecule using Gaussian on Linux OS. I have read that the essential keywords to include for such request are the...

07 November 2020 5,620 4 View

How do I calculate theoretical fluorescence spectra (TDDFT) in Gaussian 09W in selected solvent?

Good day everyone. I am new to computational chemistry and would like to integrate some part of it in my fluorescence study. I would like to investigate the theoretical fluorescence spectra using...

18 September 2020 6,742 3 View

No title

I have an AlN sample and the EDX data show me the at% of a single atom such as Al, N and O . In order to measure the at% AlN , I have to use the chemical formula 2AlN = 2Al + N 2 . should I use...

20 August 2020 6,269 3 View

What is the impact of solder mask and Surface finish on antenna performance?

Hello everyone, I am working on the design and fabrication of a butler matrix connected to an array antenna. The structure operates at 3GHz. In fact, during the design, I did not include any...

31 May 2020 1,873 2 View

Looking for protocol: mitochondria isolation from treated cell line with subsequent Analysis in Seahorse XFP (8well)?

Hey guys, i would like to know, if there is any existing protocol, how to isolate mitochondira from treated cells and use them further in Seahorse XFP Mito Stress test for 8well plates? Second...

29 October 2019 7,474 1 View

How may I clone a 5415 bp gene into pglo plasmid (5371 bp) replacing it's GFP gene (~700 bp)?

I need to clone a 5415 bp gene into pglo plasmid replacing it's GFP gene which is around 700bp long. Now PCR amplification of this 5415 bp gene using PhusionR HiFi Taq doesn't show any band, only...

05 October 2019 4,938 7 View

Wich is the post-hoc test for Conway-Maxwell-Poisson (COM-Poisson) distribution?

I used the Conway-Maxwell-Poisson distribution for my underdispersed count data. Now I'm interested in compare the treatment but I don't found the script for it. For the others dsitributions...

10 September 2019 6,835 3 View

What are some targeted sequencing options for regions of high variance?

I'm interested in sequencing a region in a bacterial genome that has high variance. This region is an integration site for various mobile genetic elements. When I PCR this region, I can see...

18 August 2019 3,129 4 View

Similar questions and discussions
What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Modeling viscosity using model of Chung?

Hello, As part of simulation of gases mixture and water, I need to calculate viscosity of the fluid components and I am using relationships proposed by Chung et al. (1988). The irony is while I...

25 February 2021 8,053 5 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close