I need to simulate Optical Signal to Noise Ratio (OSNR) vs BER and SNR vs BER plot in Optisystem v.13. So, how can I define a custom SNR or OSNR for the same.
What would be the appropriate way to plot and analyze a designed system?
You should use WDM Analyzer for both of them.
for different values of X, what will be the loop or tool in MATLAB for the below problem summation (U(n-L)(X)*(K(L)-K(L+1)), 1, n-1), where U is the function of X for different time (n-L), and...
18 April 2020 7,047 11 View
My research topic is " Factors effecting on infant mortality among the slum dwellers". For this I have to specify some independent variables which are significant or not for the occurrence of...
23 December 2019 2,390 3 View
Please let me know where one can publish research papers related to product design+solar photovoltaic+societal context ? Both international Journals and Conferences which accepts it.
22 January 2019 9,037 2 View
Dear all, I want to find Spectral efficiency (b/s/Hz) of my designed systems. For this, I need to find two factors, (1) bit rate and (2) Bandwidth required. Can we find the bandwidth from the...
05 July 2018 8,265 2 View
Hello people I am trying to simulate biomass combustion using ANSYS Fluent with paddy straw bales as biomass fuel. I want to write a UDF for that as it involves a solid phase too but dont know...
20 February 2018 6,465 3 View
Fate of Heavy Metals in Environment? Heavy metals do not degrade
19 March 2016 2,155 14 View
Dear Sir/madam, I need to separate or select a specific wavelength from a light source that consists of all the wavelengths from 410 nm to 900 nm. Please suggest me techniques available to do...
04 December 2015 7,023 13 View
Curious about publication ethics and the conflict of interest.
14 October 2013 3,231 2 View
I need to generate two carrier frequency by driving the Mach-Zehnder Modulator at optical carrier suppression modulation point. what should be the bias voltages if I want to use a 25 GHz RF...
01 January 1970 6,972 3 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...
28 February 2021 400 1 View
Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks
24 February 2021 9,378 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View
Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...
23 February 2021 1,761 1 View
Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...
22 February 2021 4,882 3 View
For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...
21 February 2021 7,624 3 View
Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...
21 February 2021 2,333 4 View
I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...
21 February 2021 3,043 3 View