Simulation buckilng
please refer the tutorials.It is the best solution for you.
Thank you
Interesting question.
Interesting
Thank you for your interest in the product
After create your sketch from simulation choose buckling study then apply load, fixture and create mesh finally save and run
interesting
In this case I recommend ANSYS for you
Thanks for our answer
I agree with Ahmed Kadhim
interested
شكرا جزيلا على سؤالكم وتواصلكم
Follow
Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...
24 February 2021 1,598 2 View
Hello dear researchers I want to use a thermal imaging camera to livestock study. I wonder which type to use. If you know or used a good type please comment or insert its online link in...
29 January 2021 4,163 4 View
explain your idea
01 January 2021 8,593 2 View
I need to use a new software in Organic and Perovskite solar cell simulation
24 December 2020 2,397 4 View
Please, can the concentration of the drug inside the nanocarriers or nanoparticles be determined using a UV spectrophotometer after getting the calibration curve of the drug alone?
19 December 2020 4,634 5 View
Some times there are missing values for some years in time series data, how to deal with this problem?
11 December 2020 1,263 3 View
I know that this system was regional before, thus covering specific areas not alla the global
09 December 2020 3,343 3 View
Hi, I need the JCDPS of polycrystalline ZnS, it would be appreciated if you could help me through this thank you in advance
30 November 2020 3,342 3 View
24 November 2020 9,036 2 View
I have synthesized NCQDs using citric acid and urea as precursors. The powder-color of the quantum dot after the freeze-dried is green; however, the color will change to black as stored at room...
29 October 2020 3,700 3 View
Hello, If i am doing a buffer exchange for an antibody of 1mg/mL, does the elution lose protein in the process of buffer exchange? For example, if i flow through 500 uL of 1mg/mL sample, and...
03 March 2021 6,299 3 View
03 March 2021 5,360 2 View
I am trying to classify and analyze the results of an SDS-PAGE based array for bacterial detection using machine learning, but I have trouble finding the best way to represent the results with...
27 February 2021 9,176 3 View
Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...
26 February 2021 3,738 3 View
In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...
26 February 2021 3,806 2 View
Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!
25 February 2021 3,092 2 View
I have set up a qPCR run on MxPro with SYBR green and ROX as a reference, however, when I go to the analysis section the program seems to only collect data for the dissociation curves and not the...
25 February 2021 8,039 1 View
I am trying to analyze lipase using the reverse phase-HPLC C18 column. In the literature, 0.1 % TFA was and 60% ACN was used. Can I use TCA in place of TFA? If any other methods are available to...
25 February 2021 2,388 3 View
Hi! I would want to know if I can use acetic acid with an ELITE WAX Perkin Elmer column for Gas Chromatography. This column has a polyethylene glycol phase, but I can't find the manual to check...
22 February 2021 730 2 View
I have calculated thermodynamic parameters for surfactant solutions in aqueous and mixed alcoholic solvents. I want to calculate the value of errors in the data and represent it in the table along...
22 February 2021 239 2 View