How to plot data from a table written in a txt file using MATLAB?

10 October 2018 0 1K Report

Hello, I have a file contains many columns and we need to plot the table in MATALB. How can we do this? The file is attached..

Thanks

Badges
Science topic

Similar topics
Filing

More Ahmed S. Mansour's questions See All

How do we correctly setup the solar ray tracing for a Photo Voltaic PV panel simulation in ANSYS FLUENT?

Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...

08 September 2019 688 2 View

What are the equations of the boundary layer of a flat plate that TDMA method is based on?

Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...

05 June 2019 8,078 4 View

How to define a heat flux and convection coefficient at the same time on a wall using user defined function in FLUENT?

Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!

05 June 2019 7,188 12 View

How can we define a symmetry wall boundary condition in Fluent?

Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...

04 May 2019 6,100 3 View

How to use Chemkin to model the model studied in the attached paper?

Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks

04 May 2019 4,064 2 View

Can we cople between ANSYS FLUENT and Simplorer ASAP?

Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!

03 April 2019 2,799 6 View

How can we define a heat flux boundary condition + convection for one wall in ANSYS FLUENT?

Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks

02 March 2019 6,112 4 View

What are the equations used to simulate a steady state thermal analysis using FEA ANSYS thermal?

Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks

31 December 2018 5,908 5 View

How can we save calculations to a text file from a Matlab CFD code during running the code like ANSYS FLUENT?

Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!

31 December 2018 934 3 View

How does this UDF of a flap airfoil work?

Hello, I have this UDF and it says that the airfoil changes the degree to +/- 8 through 1 sec, how is to work and how can we control the angle? /**********************************************/ /*...

09 October 2018 4,673 0 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

How do I replace a file with a more recent version of a paper that was uploaded to ResearchGate?

The paper in question is "Interpolation of Nitrogen Fertilizer Use in Canada from Fertilizer Use Surveys". This paper was very recently published by Agronomy (MDPI). Agronomy has, in the last day...

07 August 2024 9,934 3 View

Can I use a HisTRAP column for affinity chromatography?

I'm working on selecting antibodies against a recombinant protein that has a His-tag. My idea is to first bind the recombinant protein to a HisTRAP column and then use this column for an affinity...

07 August 2024 505 3 View

How to solve g_mmpbsa error?

Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out

07 August 2024 6,066 0 View

How do you delete a duplicate pdf for the same paper on ResearchGate?

The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.

07 August 2024 9,508 1 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

JCPDS 65-7246 file please?

Dear Researchers Kindly share JCPDS 65-7246 file Thanks in advance

04 August 2024 5,613 1 View