How to model post tension concrete using Abaqus?

More Rwayda Kh. S. Al-Hamd's questions See All

What is the way to define the PT unbonded tendon constrain with concrete ?

I am using Beam elements for the tendon due to its geometry. as shown in the pic attached. Since I cant use the embedded option as this would be fully constrain and wont be apple to do a cohesive...

10 November 2018 6,722 3 View

How to model post tension concrete using Abaqus?

I am trying to model post tension concrete beam can you please advise me the best way to conduct a model in abaqus ?

10 October 2018 2,837 3 View

Ground theory or phenomenology?

A Research aims to explore how smokers, perceive and interpret fear appeals in anti-smoking ads regarding the effectiveness of these ads when smokers experience exposing to such ads. To understand...

01 May 2018 4,504 13 View

How can I do heat transfer analysis for a Steel Channel embedded in concrete Slab using Abaqus ?

i have a steel channel embed in concrete slab and i can't run the heat transfer analysis

04 May 2017 1,461 1 View

Using Riks solver in abaqus (concrete material) ?

hello i am trying to do buckling analysis using Riks statc wit abaqus the first model was doing fine but when i have changed the material it was stopping the the first peak ! what i shall do to...

02 March 2016 8,094 0 View

Hello am trying to model crack (XFEM) in concrete and am not sure how to calculate Maxps Damage, can you help me please ?

07 August 2015 7,180 0 View

Is "TIC_TOC" is enough for measuring the execution time of the algorithm in Matlab ?

I wonder Is "TIC_TOC" is enough for measuring the execution time of the algorithm in Matlab ?!!! .. I Think I couldn't understand how this function works !!

04 May 2015 4,987 2 View

How can I measure the stress strain curve for normal concrete in tension experimentally?

Thanks in advance for your replies.

04 May 2015 1,623 6 View

Any recommendations for an optimization technique that usually gives good results?

I think PSO, Bees or ACS might help, but which one will be the best choice?

09 March 2014 8,009 15 View

Any recommendations for an optimization technique that usually gives good results?

I think PSO, Bees or ACS might help, but which one will be the best choice?

02 March 2014 8,805 16 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

Natividad Garcia

Hi! Maybe this link can help you https://m.youtube.com/watch?v=jvk4s6X0YXk. Also I recommend that you check the abaqus documentation.

Hamed Dabiri

Dear Rwayda Kh. S. Al-Hamd

To my mind, one of the ways is to assign applied loads in two steps: in the first step assign static and dynamic loads, then, assign post tension load in the second step.

best regards

Hamed

Rwayda Kh. S. Al-Hamd

Natividad Garcia Thanks :) i hope this was in English :(

Dear Hamed Dabiri

Thank you very much :)

Can clarify more why would i need to use a dynamic solver ?