How to model air engine system in MATLAB SIMULINK ?

04 April 2015 1 9K Report

As I want to create air engine simulation model in MATLAB Simulink please guide me for same. as I gone through ADVISOR also but not getting any particular direction.

Michael Gordon

Hi,

for beginning I would like to recommend you excellent book "Getting Started with Simulink" written by Luca Zamboni. https://www.packtpub.com/application-development/getting-started-simulink. To be more precise I need some overall idea. Good luck!

Badges
Science topic

More Nikhil Chotai's questions See All

Pressure drop in Pipe using ANSYS Solar Load Model Tutorial & Example

Can any body Guide me for Solar Load Model Example As i want to calculate pressure drop or increase due to heat addition due to Solar load.

11 December 2015 236 3 View

Can Pipe (TL) in Simulink Simscape be used for compressed air?

As I want to analyse the compressed air and in MATLAB Simulink simscape Block Pipe(TL) is available can use it for compressed air

09 October 2015 4,984 1 View

Best Book for Losses or Pressure drop in compressed air pipe ?

Please can any body guide me for Pressure drop or Losses in long distance Compressed air Pipe or Please suggest any Good book for above

09 October 2015 9,615 3 View

How do I apply force on piston in engine in MATLAB simulink?

As i have prepared second generation model of engine in SIMULINK and i want to apply force (if Possible Pneumatic force -compressed air flow) on piston and want to observe dynamics of...

06 July 2015 4,111 4 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

Please, what is the memory consumption of the Matlab function quad tree decomposition procedure [S = qtdecomp(I)] with respect to the input set I?

27 July 2024 5,455 2 View