How to measure the fluid pressure? How do you calculate it for fractal aggregation kinetics characteristic time calculation as shown in the attached?

More Abhisek Mondal's questions See All

How to perform Gaussian optimization for a polymeric structure?

I am trying to perform Gaussian optimization of a polymeric structure with 250 atoms. It is made up of only C and H atoms with several aromatic phenyl ring interlinked by C=C. Every time I am...

04 January 2021 9,616 2 View

Can I calculate discharge of streams/ watersheds in GIS without field data?

I am required to do a project where I have to calculate discharge of streams/ watersheds in a high altitude area with extremely treacherous terrain. Will it be possible to achieve this objective...

27 December 2020 9,101 5 View

If one publishes in a journal with impact factor >1.4 and which is not included in NAAS list of journals, will the paper be equally valued by ICAR?

I understand the difference between NAAS score and Impact Factor but is it okay to publish in a non-NAAS, high IF journal? How will it be valued in ICAR interviews and related recruitments?

10 September 2020 7,575 3 View

How can I perform sensitivity analysis using R?

I have below model: X = A*B Where A = a list of values with Lognormal distribution (size = 13) and B = another list of values with Lognormal distribution (size = 13) How can I perform 1st...

05 July 2020 1,963 1 View

We have some proteomics data from 2017 and 2018 for which the raw files are missing, but we have the processed raw data. Is the data publishable?

We are missing some mass-spec raw files from 2017 and 2018 when deposition of raw files were not mandatory. Since most of the journals now require raw file availability through ProteomeXchange,...

14 June 2020 6,064 1 View

Why second stage juveniles are used for DNA extraction from nematode for identification purpose? Can I use female or male for the same purpose?

I am working on rice root knot nematode. For identification purpose mostly second stage juveniles are used. I wonder why females or males are not used commonly for the same purpose? I am using...

26 March 2020 7,419 3 View

Is there any alternative cheaper TaqMan universal master mix available in the market other than Thermo with similar sensitivity?

I am looking for a cheaper TagMan master mix for qPCR. I use FAM labeled primers for gene expression, does anyone have any suggestions

17 March 2020 1,105 2 View

What is the effect of Bejan number on heat transfer applications?

In our case the Bejan number decreases with the increase of mass flow rate or Reynolds number of the multiphase fluids through a packed bed. However, if mass flow rate increases Nusselt number,...

27 December 2019 6,088 3 View

Is range of the induced vector measure of a Riemann-Pettis integrable function relatively compact in X?

A function $f\in X^{[a, b]}$ is said to be Riemann-Pettis integrable if $x^* f$ is Riemann integrable for each $x^*\in X^*$ and if for each interval $I\subset [a, b]$, there is a vector in $x_I\in...

27 December 2019 7,532 9 View

Higher or lower values of local entropy generation rate is desirable for the better heat transport?

Local entropy generation rate (comes from the 2nd law of thermodynamics) should be higher or lower for a heat transfer device for its better heat transport performance?

22 December 2019 5,338 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View