02 February 2019 1 8K Report

Please suggest some authentic method and/ or some Reference.

More Hafiz Md-Tahir's questions See All
How to figure out easily the right journal with the right scope for your paper?

According to my experience most of the selected journals during paper submission are based on journal text matching suggested results from Springer, Elsevier,,,Etc. then the manuscript happened to...

01 March 2021 1,786 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

What is the best way to track bird migration?

Migratory birds are globally scattered. What should be the ways to track them? Except ARGOS. Elaborate.

25 January 2021 2,355 4 View

How i can reduce the number of atoms using Vesta ?

I'm a new Vesta learner, I have downloaded cif of Ch3Nh3PbI3. Total number of atom in chemical formula for Ch3Nh3PbI3 is 12. But when i convert this cif to poscar file using Vesta, total number of...

14 January 2021 5,733 11 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

How to calculate the replacement cost of battery?

As battery needs to be replaced after the specific charge and discharge cycles mentioned in the datasheet. If we have the time series data of battery power and energy capacity, then how can we...

01 December 2020 3,433 3 View

Can anyone please elaborate the relationship between charge and discharge cycles and battery lifetime?

I am designing the optimal HESS capacity for the renewable system. I have to select the cutoff frequency of low pass filter to divide the low and high-frequency components. charge and discharge...

05 November 2020 8,397 3 View

How to select the frequency range in MATLAB Wavelet toolbox?

I have a continuous, time-domain noisy signal and want to decompose into low-frequency (LF) and high-frequency(HF) components using Wavelet Toolbox. But, I am unable to select the frequency range....

29 October 2020 5,219 5 View

How can I retrieve information of viruses reported from a particular region/country ?

Dear All, Can anyone please guide me on how to get information (sequences) of plant/animal viruses from a specific region ? Looking up the published literature is one way but its time-consuming,...

19 October 2020 3,958 1 View

Similar questions and discussions
What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Is Journal of Agricultural Research a predator?

it is published by Juniper

28 February 2021 354 4 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

Suppose we have a banana seller cart consisting of 4 wheels, weighing about 300 kg. How much torque motors are needed to pull of push it electrically?

I am thinking of electrifying the street food carts while harvesting energy using solar panels on top.

22 February 2021 4,323 3 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

Where can I obtain agricultural land use data for Wales, UK?

The Gower peninsula around Swansea is my target area

16 February 2021 7,473 3 View

How to differentiate the economic productivity in agriculture and in manufacturing sector?

Most of the references I found were on the economic productivity in agriculture but very limited application in manufacturing sector. I would appreciate if anyone could share the references on...

15 February 2021 8,342 7 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close