How to insert the power ratings of BLDC motor in MATLAB simulink block. The parameters permitted to be inserted don't include power and torque.?

06 June 2019 1 10K Report

I have a BLDC with given data (Power+voltage+current+torque). But When I use the Simulink block I can't find these parameters.

How to match the data in the two inserted images with each other?

Noralden Basil

Try to increase The Resistance i think it will solve your problem

Badges
Science topic

More Essam Ali's questions See All

How to insert current limiter in simulink?

I want to limit the current entering the battery and a load. How can I use a current limiter in MATLAB Simulink?

07 August 2019 8,665 6 View

I need an interference between the simulink and electrical simscape. any one can help me?

I have a model for powering an electric vehicle (robot) in MATLAB simulink and Brushless DC motor in electrical simscape (which is in documentation of MATLAB and In electrical simscape) and when I...

04 May 2019 9,430 3 View

I have a simulink file with matlab function. and the compiling give me an error message that the signals are "double" type. any one can help?

The compiler may take the time in calculation with current and voltage signals?

04 May 2019 3,086 1 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

How to reduce the material coming out of the torque rheometer?

A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....

25 June 2024 10,154 0 View

Dear Professor/Researcher, I want to use LoRa to send a signal with a frequency of 10 kHz. Is this feasible or not?

I use LoRa with Matlab/Simulink

23 June 2024 3,847 3 View

Aspen Adsorption linking to MATLab ??

Hi, I am looking to link MATLAB to Aspen Adsorption. I know that for Aspen Plus, it is possible to use actxserver(). Does anyone know if the same method can be used for Aspen Adsorption as well?...

20 June 2024 8,338 2 View

Does anyone know where this module is in Simulink?

I try to build a three-phase wireless power transmission model and saw this module in an article.

27 May 2024 3,471 2 View

Can you help me for do this matlab simulink project?

I'm new. I know just little use of matlab. Help me for do this matlab simulink project.

25 May 2024 4,247 1 View

Simulink model for ANC earmuffs?

Adaptive Filters are core of the ANC system. They continuously adjusts its filter coefficients to minimize the error signal, effectively generating the anti-noise signal. Common choices include...

21 April 2024 4,468 1 View

I need help designing an H Infinity controller to control a wind energy conversion system ?

What is the best approach to design an H infinity controller for a linear model of a wind energy conversion system, with the goal of simulating it in Simulink? Any specific methods or tools...

26 March 2024 4,008 1 View