Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

QTL, recombination frection?

22 February 2021 2,588 2 View

What are the dimensions by which the independent variable (big data) can be measured, Knowing We using the questionnaire instrument?

We have a research project consisting of three variables where big data is the independent variable. Some previous studies showed that Volume, Variety, Velocity and Veracity Are the dimensions...

21 February 2021 8,133 2 View

What is the difference between PBE and PBEsol functional?

Hello, I am a 3rd year chemistry student and I'm writing my project report on computational chemistry. does anyone know how PBEsol improves upon the PBE functional? Thanks in advance

19 February 2021 7,068 4 View

Can someone help me with this error that I am getting while estimating a VAR model in R?

I am using annual time series data to estimate a VAR model in R. However, when I run the command to find the optimal lag length, I get the following error: Fehler in VARselect(data, lag.max = 10,...

18 February 2021 9,647 3 View

How can we determine the band gap of a composite material that is made up of a composition of direct and indirect band gap semiconductor materials?

I have a direct band gap material and an indirect band gap material. If I made a composite of both through physical mixing. Then how can I determine the band gap of such a material as the Tauc...

17 February 2021 8,104 4 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why am I getting 'Infinity' and 'NaN' in my mixed-mode energy release values?

Hi everyone, I am currently running a mixed-mode simulation of a DCB using a user-defined cohesive zone model (UEL), however, the results I am getting don't make sense. I used the same UEL for...

24 February 2021 4,157 1 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Why does the sum of reaction forces not match the force component of a Free Body Cut in Abaqus?

I am using Abaqus to simulate a plate with in-plane loading. The boundary conditions allow the right edge to move up and down, the displacements on the left edge are fixed. There is no rotation...

23 February 2021 711 3 View

How to reduce static electricity of powder after lyophilization?

I am working on synthesizing and then purifying peptides using the SPPS system. After purification of the peptide, the peptide powder is obtained using a freeze dryer. When measuring the powder,...

22 February 2021 10,099 5 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

How can I obtain Reaction Forces in ABAQUS?

I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...

21 February 2021 3,075 2 View

What cause the beating of this signal?

I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...

19 February 2021 5,872 3 View

Small displacement measurement in vacuum?

Hello, I have a question. there is a circular thin foil which vibrates in vacuum, the foil restricted and moves up and down. it is like a diaphragm between two pipes . both sides are in vacuum but...

18 February 2021 8,075 3 View

Abaqus: deactivate displacement boundary condition?

I am running analysis of a cross-shaped sample that is prescribed a displacement along x and y-axes. I have run several jobs with this model and had no issues. However, the current set of...

15 February 2021 1,680 8 View