How to know if Zinc Oxide is coated on the glass substrates?

Hello all I have prepared Zinc Oxide nanoparticles using sol gel synthesis. I tried to coat the ITO and glass substrates with the ZnO nanoparticles ( dispersed in ethanol). But I am not sure if...

08 December 2020 3,692 8 View

Which PEIE to use?

Hello all Thanks for answering my previous questions. I am making perovskite LED and intend to use PEIE on zinc oxide layer as ETL. But I am not sure what version of PEIE to us. There is the one...

08 November 2020 5,710 3 View

Zno NPs seperation?

Thanks a lot for your answers. I have one more question: after synthesizing ZnO nanoparticles , I am not able to separate from the original solution (dispersion actually). The recipe is as...

23 October 2020 9,857 8 View

How to do PBABr synthesis?

I am following this recipe for PBABr synthesis. I added HBr (48 wt % in H2O) to Methanol and PBA solution at 0 degrees celsius. But after 2 hours of stirring I am not able to see precipitates. I...

08 October 2020 6,485 4 View

Which factor controls Peak intensity in Rietveld refinement?

I am refining structural parameters of my sample. after inserting all parameters in sequence, When I take first Run in refinement, the intensities of all peaks diminishes to zero of calculated...

07 October 2020 8,598 1 View

ZnO and PBABr synthesis?

Hello all, I want to synthesize ZnO nanoparticles and PBABr in my lab for my LED project. I know the method, but I am not sure how can I check(even visually) that I have arrived at the correct...

27 September 2020 5,334 7 View

MoO3 RF Sputtering?

Hello all, I have to do RF sputtering for MoO3 for my LED project. But I have come across many recipes for reactive RF sputtering of MoO3 ,using Mo as a target and Oxygen as the reactive gas But...

16 September 2020 5,222 2 View

How to apply axial load to a tapered roller bearing segment to determine axial stiffness?

Hello Everybody! I am currently writing my master thesis in which I am trying to understand the stiffness values of tapered roller bearing. For this, I am have made the model simpler by using only...

01 September 2020 8,843 2 View

Can we define the external quantum efficiency as the (number of photons emitted/ electrons injected) for n LED device?

I have come across the definition for EQE as the number of radiative recombination events out of the total number of recombination events in the LED. But is it safe to say that EQE = number of...

07 July 2020 3,023 1 View

How to obtain corrected PL spectrum?

Hello all, I am intending to measure the PL spectra for my perovskite samples. How can we obtain a corrected PL spectra in the spectrometer, independent of the photoresponsivity of the silicon...

29 June 2020 7,298 5 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View