01 January 1970 1 7K Report

I am trying to determine the corrosion rate of super duplex stainless steel using Palmsens.To start with the potentiodynamic polarization test in Palmsens the value of Equivalent weight of Super Duplex stainless steel has to be computed.

More Binsu Babu's questions See All
SEM micrograph interpretation??

An image in one of the SEM micrograph shows "S3400 15.0KV 67.3mm x 6 SE". Can anyone say me what does it mean ? How much magnification should I consider? shall i consider 6X as the magnification...

01 February 2018 195 11 View

What is dislocation density and how does it increase or decrease?

general question with respect to material science. Needed to understand the cause behind increase or decrease in dislocation density

11 December 2017 10,014 1 View

How to develop processing maps for hot metal forming operations?

My project work is based on "Structure property correlation of forged alloy steels".The sample in which I have performed hot compression test is F55(super duplex steels).I am not able to find out...

01 January 1970 8,356 18 View

Similar questions and discussions
How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Difficulty with permittivitt and Magnetic Permeability Calculations?

Difficulty with permittivitt and Magnetic Permeability Calculations Hello everyone, I have all the parameters related to the calculations of the permittivitty and magnetic permeability...

30 July 2024 5,206 1 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

All math can be explained by iterator of code?

all math can be traversed by code? all math can be translate to code?

26 July 2024 9,530 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close