How to find active surface area of catalyst and catalyst active sites?

More Takwa Chouki's questions See All

What is the reason behind the high current density of Platinum coated materials Linear sweep voltammetry (LSV)?

I prepared platinum coated graphite and I made LSV test ,I found out that the current density was too high arround -8 mA/cm2,I want to know the reason behind that and what to do to fix it?

21 August 2019 7,279 3 View

What is the best way to keep an anaerobic chamber anoxic in the absence of hydrogen?

I'm a graduate student who works with an anaerobe, so I often work in an anaerobic chamber. I've been working on an assay that involves the steady-state of the quinone/ quinol pool. Anoxic...

03 March 2021 2,971 1 View

How do I increase the yield of my PCR product?

Hello, We would like to increase the yield of our PCR product. We are running a series of PCR reactions that is targeting ~1.1kb sequence. We begin each reaction with ~400pg of template DNA...

02 March 2021 4,029 3 View

How to polymerize TEOS?

I want to polymerize TEOS on a surface. I know that NH4OH is a preferred catalyst and an alcoholic solvent should be used .But I can not find certain amounts of each material to use. Does any one...

02 March 2021 1,404 6 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

Runs of nucleotides in Sanger sequencing?

I performed site directed mutagenesis, transformation, and then I sent out plasmids for Sanger sequencing and found out that there is extension of DNA just before the stop codon. I am not sure...

27 February 2021 547 3 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

Calculating volume of DNA required from DNA concentration?

Hi I am a bit confused. They are asking me to find out the volume of DNA required in ul (a total of 30-100 ng for genomic DNA) from the DNA concentration in the nanodrop reading which was 404.8...

26 February 2021 5,029 2 View

Luma M. Ahmed

I interest.

Bahram Hosseini Monjezi

Dear Takwa

I recommend you to take a look at the article below:

Electrochemically Active Surface Area Measurement of Aged Pt Alloy Catalysts in PEM Fuel Cells by CO Stripping

https://www.osti.gov/servlets/purl/1425404

Regards

Takwa Chouki

Thanks Bahram Hosseini Monjezi

Amravati Singh

hi @ Takwa Chouki

go through this question on researchgate

How to calculate electrochemical active surface area (ECSA) for Pt based material from a CV curve in 1 M H2SO4 solution?

by Soumen Dutta

37.83
Hanyang University