How to detect and correct skew of the scanned document image.

Htet Yamin Ko Ko @Htet_Ko_Ko2

01 January 1970 0 7K Report

I found that Hough Transform is used for skew detection and correction but I don't know how it is work.

The input image is scanned paper currency and I want to correct the angel.

Badges
Science topic

Similar topics
Correction

More Htet Yamin Ko Ko's questions See All

I would like to extract second order statistical texture features from the approximation coefficients of the 2D-DWT.

Is it possible to calculate energy, contrast, homogeneity, etc by using approximate coefficients of 2D-DWT and the histogram of LL Band image of 2D-DWT. I didn't use GLCM for some reasons.

02 March 2017 1,472 2 View

What are the pros and cons of Learning Vector Quantization neural network?

I want to used learning vector quantization neural network as a classifier for currency verification system.

01 January 1970 7,742 0 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

What test should I use to compare two or three means, if data is not normally distributed but sample size is > 30 in each group?

I personally feel this as a most confusing question. As per my understanding, if sample size is > 30, and sample is skewed, we can still use paramteric approach, as it will follow Z...

01 March 2021 1,587 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to find a correlation between coordinates in a curvilinear coordinate system?

Hello. I have a skewed elliptical coordinate system (I use alternative elliptical coordinates). And I need to determine connections between coordinates in order to fetch a covariance matrix of...

28 February 2021 364 3 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View