13 February 2018 5 2K Report

Please share me some tutorials to design the Nanocomposite using SOLIDWORKS

More Dinesh Babu Rathina's questions See All
1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Sensitivity analyze for crop evapotranspiration (ET0)?

Does anyone know how to perform a sensitivity analysis for crop evapotranspiration ( FAO Penman-Monteith equation) using daily meteorological data?

27 December 2020 9,552 3 View

How do I DERIVE equations for lumped elements (R, L, C) from S-parameters?

I have modeled the lumped element circuit for the 3D structure which has been simulated in HFSS. Now I need to derive the equations for the lumped elements keeping the S-parameters of the...

23 December 2020 172 3 View

No title

For academic writing.

17 December 2020 6,465 5 View

How to get nanocomposite of PEEK with Zirconia ?

Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...

13 December 2020 4,329 5 View

Choice of sampling time in discretization of control?

What I understand is while applying continuous control to a continuous-time system in MATLAB simulations, actually the control is being applied in discrete manner inherently due to the nature of...

28 November 2020 1,866 4 View

Simulation of sliding mode control for a maglev system?

I tried to simulate a maglev system with continuous time sliding mode but my simulation is showing error (there is a singularity at one of the integrators). I am attaching the modelling and...

16 November 2020 8,964 7 View

Can anyone suggest is there any way to compare the amount of chattering in 2 approaches of sliding mode control in quantitative way physically ?

Suppose 2 methods are shown to do sliding mode control of a given system. Please tell me if we can compare chattering in both by MATLAB or some other way

16 November 2020 3,251 3 View

How can I get eggs of an univoltine casebearer moth for a threshold study?

I am planning to conduct a cage study to determine a critical density of an univoltine casebearer moth in red clover seed crop. This requires to release first instar larvae in the cages with the...

02 November 2020 6,577 3 View

Can anyone suggest me free and fast scopus publication with highly acceptance rate?

Q3,Q4 will be okay. I need scopus publication without APC and fast published. The paper is from Computer science discipline.

19 October 2020 4,255 4 View

Similar questions and discussions
Which method is preferable for cutting the nanocomposites?

Which of the methods like water jet cutting, diamond cutting, laser cutting, etc. is more suitable to cut the carbon nanotubes reinforced epoxy composites into test sample to ensure the clean...

29 January 2021 1,354 5 View

What is the harmless way of cutting epoxy filled nanocomposite ?

I want to cut epoxy filled nanocomposite for FE-SEM analysis. What is the best way to cut it without resulting in any cracks or change in position or alignment of the particle reinforcement ? Also...

28 January 2021 7,084 5 View

How to get rid of the solvents from a PU-Ag nanocomposite?

I've synthesized a polyurethane-Ag nanocomposite and the product is dissolved in a two-component system i.e. DMF and DMSO. I wish to know of any ways that I can use to get rid of the solvents and...

27 January 2021 1,847 3 View

Why degradation of pesticides is maximum at specific pH by using nanoparticles and nanocomposite?

actually, I am degrading pesticides by using inorganic composites the pH of the pesticide in distilled water is neutral the pH of nanocomposite is also neutral then why maximum degradation takes...

23 January 2021 8,775 3 View

In the tensile test for a nanocomposite sample, if the sample width decreases (thickness is constant), what does the stress-strain curve change?

Given that the stress is equal to the force divided by the area(width*thickness), what change does the reduction in sample width make to the stress-strain curve? Does stress change occur...

09 January 2021 5,124 5 View

How to perform adsorption kinetics ?

I am trying to do a kinetic study. I am using graphene- organic compound nanocomposites to show heavy metal removal. I have plotted the graph of nanocomposite against metal ions with respect to...

05 January 2021 8,667 3 View

How to prepare the sample of polymer nanocomposite for SEM analysis ?

Does Epoxy clay nanocomposite sample require surface preparation. I am going for Gold sputtering to make the surface conductive. I guess there is no need to clean or polish the surface beneath the...

04 January 2021 1,943 8 View

What method is more useful for prepare metal/ metal oxide Nanocomposites?

If possible any easy preparation method

31 December 2020 1,662 3 View

How can we confirm the formation of heterojunction in nanocomposite systems ?

IV measurement and KPFM

21 December 2020 9,658 4 View

How to get nanocomposite of PEEK with Zirconia ?

Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...

13 December 2020 4,329 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close