Hello fellow researcher .. What is the meaning of your name?

I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.

03 March 2021 5,266 4 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Which is better medicine or food in obesity?

Preference in terms of the scientific aspect

28 February 2021 796 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

How to find natural frequency of a bridge from vehicle induced vibrations?

i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...

22 February 2021 10,004 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

No title

25 February 2021 5,713 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View