19 January 2023 0 1K Report

XP-PCM model is an extension of pcm model in xp-pcm model we have to change scaling factor and also add pauli repulsion .. So what key word I have to use to define these parameters in gaussian 16..

More Abhay Chauhan's questions See All
Is there an English Translation of the Carl Moller text: ZUR VERGLEICHENDEN ANATOMIE DER SILURIDEN?

I recently came across an anatomy text by Carl Moller that was published in 1915 but it is in German or Dutch neither of which I can understand. I would like to know if there is an English...

10 August 2024 4,347 1 View

How to do Pre Merger Financial Perfomance Analysis?

For Example, Company A & B merged with Company C , so during the pre merger period there are 3 company so how to do its pre merger analysis with post merger company? (either its 1 to 1 or 3 to 1)

31 July 2024 2,503 3 View

How to estimate a protien's size using Chimera or PyMol? how correct this estimated can be?

I need to know the approximate size of my target protein for Negative-stain EM. I have an alpha-fold predicted structure of the protein. I do not see any turtorial on internet for estimating the...

21 July 2024 5,732 3 View

What publications should I target as a psychology masters student in the UK?

I am writing a paper as a part of my course. I am new in London and was wondering that what publications should look upto?

21 July 2024 3,538 1 View

I have two problems: 1) the enzyme is not immobilizing efficiently into the MOF material.. 2) the MOF itself has peak on 400nm by using p-NPA test.?

I am working on carbonic anhydrase immobilization into MOFs. I am facing problems with low enzyme loading.. The other issue is that when using p-NPA activity test to detect the activity of the...

20 July 2024 1,440 3 View

What analysis to use for an dependent variable with repeated measures and a independent variable only measured once?

Hi all, I am trying to use mixed effect model to analyze my data, which including a baseline measurement for my exposure (A), and repeated measurements for the outcome (B). I do have some...

17 July 2024 8,682 3 View

I need to know the required time for VDF heating with water for 50-80°C for PVDF Polymerization in ?

i need to know the required time

15 July 2024 4,796 2 View

How to bring baseline to zero for an absorbance data for chromatogram?

I forgot to autozero during the run (Size exclusion chromatography.) and later i realised i forgot to do that and the baseline was not zero but below zero (and in some cases it above zero). I...

15 July 2024 5,551 6 View

How to identify a monomeric protein species of the target without running the molecular weight standard on SEC?

I was using Superose6 10/300 Gl column for purification of my target protein. the sample consists of various oligomeric state and i would like to identify the approximate elution volume where my...

15 July 2024 5,157 2 View

What analyzes do you use to compare biodiversity in a square, at two different times?

e.g. moment one: square in its normal state moment two: square after cutting large trees and replacing them with dwarf trees.

12 July 2024 8,258 5 View

Similar questions and discussions
How to convert magnetic conductivity from SI to lattice units?

I'm simulating a magnetohydrodynamic problem of blood flow using lattice Boltzmann method in lattice units and I need to convert the magnetic conductivity to lattice units. The physical value is...

07 July 2024 5,243 0 View

How to decide mass scaling in ABAQUS?

I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?

01 July 2024 3,749 0 View

How to adjust or recalibrate negative MFI values from cytometer?

I am looking at puromycin incorporation rate by flow cytometry using a specific anti-puro-antibody which I use to stain different cell types. For some cells the signal is high (i.e. Puro MFI),...

12 June 2024 1,110 1 View

What is the scaling factor for DFT/B3LYP/6-311++g(d,p) level of theory for optimization and frequency analysis?

I have read some papers but i didn't get proper answers. In some cases, my level of theory is not exactly written. I will be very gladfull for any recommendation

10 June 2024 9,929 1 View

How can I obtain friction velocity(u∗) and scaling humidity (q∗) values in order to calculate transfer coefficient for latent heat(Cez)?

I want to calculate the latent heat flux(Qe) and for that I need the Cez value.

03 April 2024 6,844 3 View

How to normalize expression data with SEM?

Greetings. Probably the question is not complex at all, but can't find an answer. If I have RT-qPCR data of gene expression in a sample with multiple analitycal replicates - to compare it to data...

13 March 2024 7,640 1 View

Mass scaling in ABAQUS ?

I need to perform mass scaling for a certain period and remove it in further analysis in Abaqus. Does anyone assist me with this?

04 March 2024 3,203 1 View

How to calculate y+ analytically before the simulation if we have fully developed flow for the Annular pipe (a double wall bounded)?

I have a fully developed pipe flow in with Inner radius (r) and outer radius (R), using pressure driven flow condition due to buoyancy, - (1/rho) dP/dx = g and velocity scaling u* = sqrt ( (-R/...

09 February 2024 3,727 3 View

Staff burnout (Jones, 1983) scaling?

I am trying to use Staff burnout for health professionals by Jones, 1983. How is the measurement done. Please mention Likert Scale values.

05 February 2024 7,234 0 View

Scaling a business is a common challenge for entrepreneurs. How can student entrepreneurs manage this while juggling academic responsibilities?

# student entrepreneurs

20 December 2023 4,348 14 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close