Why the steel tube were strtched at the end of analysis ?

Dear all, Iam working in CFST column under cyclic loading in abaqus program, at the beginning of analysis all the mesh was fine, but at the end of the analysis there some deletion and stretching...

08 April 2019 4,840 2 View

How can one Determine the LTE Uplink resources of the access network and uplink resources in data transmission M2M communications?

The system is consisted of a single cell with one BS at the center with the following parameters :- * N=5000 (number of M2M nodes). * TRA=1000 sec. (the time interval between two consecutive...

13 August 2018 9,265 2 View

Kidney stone: study of medical geochemistry ?

Please provide me with an illustration of XRD and IR card.

03 April 2018 7,551 4 View

Has nano-emulsion fuel technology been applied on an industrial scale?

Nano-emulsion fuel technology has been around for some time. However, its use has not yet been fully established for different reasons. I would be interested to know of any plant or industry where...

03 April 2018 6,062 3 View

Does any one have these books (X-ray diffraction and IR) and the identification and analysis of kidney stone ?

Please provide me...

03 April 2018 2,613 0 View

What is suitable software for surface Finite Element mesh on a sphere?

Any advice on suitable software to generating a triangular Finite Element mesh on a sphere of unit radius and extract the nodes and connectivity files?

11 December 2017 8,069 0 View

Which software is best for below 3D mathematical representation figure?

Hi there, Could you please mind the attached figure and comment to which free software best for drawing such figure without the need to have mathematical equations for drawing the curves? Notice...

10 November 2017 5,711 3 View

Do I have to get consents for thousands of samples in my ethical approved retrospective study ? What about passed away poeple ?

I have an ethical approved project to conduct retrospective and prospective studies on sickle cell disease . I need the old DEXA scans , MRI , bone scans , CBC , HPLC and biochemistry results for...

05 June 2017 2,702 2 View

No title

01 February 2016 3,758 3 View

Is writing a medical report which is not compitable to the patients medical file is a medical error ??

I

10 November 2015 3,215 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View