How to calculate the shear modulus and youngs modulus of the AFM cantilevers?

09 September 2018 0 9K Report

I need to measure the shear modulus of the AFM cantilevers. The cantilevers which I am using are antimony doped silicon (n-type Si) cantilevers coated with Pt/Ir conductive coating.

Please suggest some methods.

Thanks

Badges
Science topic

More Sai Saraswathi Yarajena's questions See All

PEDOT:PSS polymer is not getting spincoated on PET substate?Can anyone suggest some methods to get a film of it around 100nm of it using spin coating?

CleviousTM PEDOT:PSS PH1000 is a highly conductive polymer. I need to spin coat it on PET substrate. When I place a drop of the solution on my substrate, it is forming some bubble with large...

07 August 2018 6,070 8 View

How to form a Self Assembled Monolayer of Dodecanthiol capped nanocrystals on Glass or Si/SiO2 Substrate?

Please let me help in understanding the mechanism and process behind forming SAM on any substrate. How to choose the functionalizing agent to be coated on substrate that incorporates self...

01 February 2017 5,410 0 View

Can Nitrogen be used in place of Vacuum for degassing Solvents in organometallic reactions?

Please mention for which kind of reactions Vacuum is preferred for degassing the solvents. Thanks,

11 December 2016 3,570 0 View

What will be the fermi energy level for Quantum Dots at room temperature? Is it same as fermi energy of bulk material?

How it actually varies with size of quantum dots.

09 October 2016 3,411 3 View

How to find the specific Surface Energy of bulk crystal Theoretically?

Can we estimate surface energy from thermodynamic properties? Thank You

08 September 2016 8,436 0 View

How to find the optimum temperature at which Detectivity of a Quantum Dot photodetector will be maximum?

Please tell the methods to find them theoretically and also experimentally.How does higher mobility allows quantum dot detector to operate at relatively higher temperature? Thank You.

07 August 2016 1,261 1 View

How does the Intraband Transition of carries accounts for Photoconductivity in Quantum Dots?

Suppose the light source is excited on Quantum Dots such that its equivalent Debroglie wavelength exactly matches with one of the intra band Transition Energy of Quantum Dots. What are the...

06 July 2016 919 4 View

How to remove Organic Ligands that are attached to the self n-type doped Colloidal Quantum Dots ?

Boiling point of organic ligands will be very low compared to Quantum Dots, can these organic ligands be removed by heating the film. Then what are the ways to do surface passivization if ligands...

06 July 2016 7,765 7 View

How to make a miniature( say 1-2 cm square area) Black body radiator that will work at room temperature?

Can we fabricate a simple Black Body radiator that works at room temperature( from theory room temperature black body radiator has emission peak at 10um wavelength ), can we vary this emission...

06 July 2016 2,609 5 View

What materials can be as ETL(electron Transport layers) and HTL(Hole Transport Layers) that are transparant to Mid and Far Infrared Range Radiation?

Please specify both organic and Inorganic materials for ETL and HTL.

06 July 2016 2,315 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

Stability of the Solar System: Insights from Einstein’s Equations ?

The stability of the Solar System is a complex subject that blends the classical framework of Newtonian mechanics with the modern insights provided by General Relativity (GR). Understanding this...

07 August 2024 2,569 1 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View