Why Carbon filament is elastic at room temperature and becomes plastic when heated by current?

Why Carbon filament is elastic at room temperature and becomes plastic when heated by current? How to understand the phase transition from crystalline to amorphous ?

04 May 2018 4,784 2 View

What is the reason behind the change in d-spacing and crystal plane of ZnO nanoparticles, when the dopants of Mn and Ag ions added in the ZnO matrix?

I have synthesized undoped, Mn and Ag-doped ZnO nanoparticles. The HR-TEM image indicated that the nanoparticles are structurally uniform and well-oriented lattice fringe of d-spacing around 0.23...

06 July 2015 4,818 10 View

How can I completely dissolve ZnO and TiO2 Nanoparticles?

Is there any organic solvent to dissolve the ZnO and TiO2 Nanoparticles.?.

03 April 2014 8,606 13 View

Which components should be used in Crystalline Size and Strain estimation?

1. About crystallite size estimation. XRD peak broadening is produced by both size and strain. The XRD peak full-width-at-half-maximum (FWHM) cannot be used for crystallite size estimation...

31 December 2013 6,261 4 View

How can fabricate a laser diode and photodector, monolithcally in single substrate?

Epitaxial Growth of III-V compound semiconductors in a substrate, How can I fabricate laser diode and photodector monolithcally in single substrate? How to isolate both structure and electrical...

02 March 2013 9,465 1 View

What is the difference between Room temperature PL and Low temperature PL?

Which one is best for luminescence studies of Nanostructures?

11 December 2012 7,114 15 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View