How the parameters of Permanent Magnet DC (PMDC) Generator MATLAB Simulink block can be set for particular voltage, power, current and speed rating?

Ramesh Kumar @Ramesh_Kumar92

07 July 2018 0 7K Report

What will be the Torque constant value in Nm/A, Inertia etc?

How shall we calculate them?

Badges
Science topic

More Ramesh Kumar's questions See All

What can we do to get constant voltage from photovoltaic array during variable irradiance and temperature for connecting it with dc bus ?

Is it possible to harvest maximum power point tracking for getting constant voltage?

04 May 2017 2,948 8 View

Is there any machine to do real time pcr?

I want to know how do you make real time pcr solation ? is there any machine to make it? thanks for answering

05 August 2024 1,660 0 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

Is it necessary to attach fluorophore at 3' end in MIC RT PCR machine for Dual hybridization Probe designed especially for genotyping assay?

I designed 2 dual hybridization probes for my single SNP. where I attach my fluorophore 5'-FAM-nnnn-BHQ1-3', and 5'-HEX-nnnnnn-BHQ2-3'. I need to run it on the MIC RT PCR machine by Biomolecular...

28 July 2024 5,658 0 View

Can anyone help me with in providing the procedure for purification of GSTtagged protein by gst affinity chromatography without an automated machine?

Purification of gst tagged protein

25 July 2024 1,720 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

Does anyone know if there is a lab scale encapsulation machine available for purchase?

05 July 2024 3,889 1 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View