Will silver coating be able to hold such a high temperature? And will there be any effect of coating thickness?
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,722 1 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 940 3 View
Hello all, I wanted to know, can I use galaxy (USA, Europe or Australia) platform for analyzing the shotgun data, and can it be used for publication purpose as well? Thanks :)
06 August 2024 6,610 4 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?
02 August 2024 7,185 6 View
Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?
31 July 2024 5,824 0 View
What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?
30 July 2024 6,259 4 View
If the pairs are similar, will it reduce the adhesion due to electric charges?
29 July 2024 3,182 2 View
give suggestions
22 July 2024 5,663 2 View
I am performing fluorescence experiments using a ligand to detect metal ions. I want to determine the Lowest Detection Limit (LOD) using the formula LOD = 3σ / K. However, I'm uncertain about...
19 July 2024 1,084 1 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,140 3 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,297 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,524 4 View
Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.
07 August 2024 8,782 3 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,365 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 724 3 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...
30 July 2024 433 3 View