How to obtain regions around the person bounding boxes(excluded the detected people in scene)?

Hi all. I have a set of coordinates of bounding boxes for AVA Dataset. This dataset is used in action recognition. My goal is to get the areas around the people (people are inside boxes) and do...

13 February 2021 2,538 2 View

What is the air and water fraction in wave induced spray or splash?

Hello everyone, I was wondering when a wave spray or splash occurs due to wave breaking, what is the percentage of water or air in the volume of spray that we see? I need to have a rough...

21 January 2021 7,738 1 View

Have I add research Q beside research Objective ?

In my thesis should I include both Research questions and research objectives, or I can include research objectives only.

07 January 2021 9,793 3 View

How do we explain the results of the HPLC-MC analysis?

How do we explain the results of the HPLC-MC analysis I need help in how do I read my analysis results of PHLC-MC in the form of a graph? Is there a book or website can help. Thanks

07 January 2021 9,025 2 View

What is the most suitable NMR solvent for carbon-based materials?

What is the most suitable NMR solvent for carbon-based materials?

25 December 2020 5,020 4 View

Effect of vibration on Heat transfer of fluid in pipe - COMSOL Physics?

We have a one meter long copper pipe through which water passes at a certain speed. The outer wall of the tube is covered by the heater where all the energy of the heater is transferred to the...

21 December 2020 8,954 8 View

Effect of adsorbent porosity on efficiency of adsorbent recovery ?

Hi guys. Can anyone answer the following with citing the references? 1) Relationship between adsorbent porosity and adsorption/desorption rate? 2)Relationship between porosity and adsorbent...

31 October 2020 6,323 5 View

What is Chemical Oxygen Demand (COD) Analysis?

Hello. I want to complete my information on water and wastewater and methods of effluent analysis. What is effluent COD measurement methods?

27 September 2020 2,302 5 View

How to capture the geometry of rubble piles / collapsed structures beneath the surface via remote sensing?

Hi dear community, I am currently working on a project where I want to generate a 3D reconstructed model consisting of rubble piles (in consequence of a building collapse) via remote sensing. In...

10 September 2020 4,685 4 View

How can I insert an assembeled system, meshed by SOLIDWORKS, to ANSYS?

I already did it before but this time as the model is complicated I have faced with tis error: The surface mesh is intersecting or close to intersecting,making it difficult to create a volume...

05 September 2020 9,558 1 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

How can the modification of garden soil cause global warming?

Hello, I am working on a soil project and I found a primary research article that tests how the modification of agricultural soil can cause global warming, using a thermal collector, however I...

02 March 2021 7,161 3 View

How does Scientist/RG community evaluates a case study article and the impact of it on a researcher career?

An article that is published as a case study in the SJR listed journal. How much value is added to a researcher career? How it is evaluated by a scientific researcher/University admission...

02 March 2021 9,661 3 View

Does anyone know how to plot my station to a section plot on Ocean Data View (ODV)?

I made a vertical section plot with WOA .nc file on ODV, and now I want to plot my stations (csv. file) in it. Does anyone know how to import my points to the section? They are two different...

01 March 2021 3,610 1 View

Does anyone know to clarify these changes?

01 March 2021 1,290 2 View

How can I convert .vesta file to a .cif file?

I've used the "export data" option in Vesta software to convert my unit cell into a cif file however when I use that cif in atomsk it shows error such as "can't read the position of atom 0". If I...

28 February 2021 4,966 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

No title

25 February 2021 5,713 1 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View