How does the modulus of rupture determine the safety of a structural member?

22 May 2024 1 7K Report

In terms of strength and elasticity, that a structural member can endure when subject to Dead loads over some period of time.

Adrian González Méndez

The modulus of rupture is determined in a bending test. The bending test is based on the maximum stress at fiber rupture, and the maximum shear stress at failure. Typically, modulus of rupture refers to a three-point bending test on materials.

Badges
Science topic

More Hubert Sule's questions See All

Modelling cost-of-living differences and their impact on trade competitiveness?

Wood (“Give Heckscher and Ohlin a Chance!” Review of World Economics, V. 130, No. 1, 20-49) argues that since capital is internationally mobile, capital cannot be the basis for comparative...

07 June 2024 671 5 View

Which hydroxyethyl cellulose is stable at pH -1 ? Which geller for a trichloroacetic acid skin peel?

I did increase viscosity of a trichloroacetic acid solution with hydroxyethyl cellulose. Works good for 30 minutes, then viscosity drops like a brick! No wonder, at pH -1.0 but still HEC is...

08 April 2024 6,882 0 View

Where to get public/free access CT Data for testing L3-SMI computing?

Dear RG group, I'm willing to evaluate a set of sarcopenic patient who underwent CT imaging. Before evaluating this set, I would like to test my computing of L3-SMI with CT (L3 skeletal muscle...

03 April 2024 9,212 0 View

How can you gel a trichloroacetic acid solution?

How can you gel or increase viscosity of a trichloroacetic acid solution? It seems carbomer and Na-CMC are degraded rapidly by the very acidic TCA, while HPMC drops out of solution at higher TCA...

07 February 2024 6,324 5 View

How to determine band gap energy energy from differential pulse voltammetry (DPV)?

Hello everyone, To date I’ve been calculating bandgap energy (BGE) from cyclic voltammetry (CV) measurements, as a difference between oxidation and reduction peaks’ onsets. The organic compounds...

14 January 2024 9,518 1 View

Do you know a Worldwide time series of employment by ISIC sector?

Greatings. I am looking for internationally comparable data, if possible from a single source, giving the number of employees by ISIC sector. If possible in full-time equivalent, 1995-2020. To...

24 November 2023 1,440 1 View

What is the per-sample cost of eDNA/metabarcoding?

What is the per-sample cost of eDNA metabarcoding (lab work and bioinformatics, not sample collection)? I'm not convinced that eDNA is always easier to scale than traditional monitoring...

27 September 2023 3,098 3 View

Physical and biological characteristics of Fonio and its impact on the soil fertility?

physical and biological characteristics of Fonio and its impact on the soil fertility?

17 September 2023 2,927 2 View

Why the distance from the road is considered as an important input feature for machine learning earth science models?

#machinelearning #earthscience #geoinformatics

30 March 2023 2,656 2 View

The impact of shade trees on the growth and development of cocoa seedlings?

both the positive and negative effects of shade trees planted along side young cocoa seedlings on the field.

04 March 2023 1,277 3 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 940 3 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,545 2 View

Why am I observing very high Temperature and Pressure Increase using NPT Ensemble?

Hello everyone, I am running DFT with CP2K software at 1200 K, 1 bar with a periodic system of 64 Al atoms + 2 CO2 atoms. However, I am seeing my temperature slowly increase to >4000 K and my...

22 July 2024 3,177 0 View

A twin-shaft kiln or a rotary kiln for lime production 1 class? if compressive strength of limestone is low 60 MPa?

My research work is related to the calcination of limestone. I have a complex question and would like to consult with experts in this field. Could you please advise which kiln to choose (a...

18 July 2024 1,390 2 View

How to find peak period and significant wave height for a particular location in ocean?

I want to develop the figure like attached figure. How can I get, peak period and significant wave height at any given location.

13 July 2024 886 2 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

Can someone explain the pros and cons of mean squares vs. Baker's ratio for pinpointing gene action in line x tester designs?

In plant breeding research, line x tester mating designs are often used to assess gene action for various traits. Some studies suggest that the simultaneous significant mean squares for lines,...

30 June 2024 4,877 2 View

How to calculate Module Young from compressive strength and strain curve ?

How to calculate Module Young from compressive strength and strain curve

29 June 2024 816 3 View

Where i can publish a reasearch ion history?

I wan magazin within SCOPUS

22 June 2024 2,886 0 View