Generating image artifical dataset, how?!

Dear all, I am not an expert in image processing. I have an set of jpeg images which I need to extend its size artificially, for example, add some noise, change luminance, chrominance etcc... how...

05 June 2017 739 4 View

How to use the a priori information in Soft output Viterbi Algorithm?

02 March 2016 6,382 2 View

How is noise spatially correlated in wireless channel?

In wireless sensor networks or mobile networks, when the physical phenomena does not exist or where the base station is not transmiting any power, the mobiles or sensors will receive only a...

10 November 2015 8,135 4 View

How can I estimate the signal value (Energy) at a two different nearby positions?

Suppose we have two sensors which are close to each other and the first has its own measured signal value, how this sensor can have an idea, margin or estimate of the signal measured by the second...

09 October 2015 8,764 10 View

What is a model for observations/data distribution is wireless sensor networks?

In WSN, the collection of N nodes have to observe and have a measure about a certain physical phenomenon. Please, anyone can provide a reference/paper that provides a statistical model that well...

09 October 2015 9,398 5 View

How can a Matlab mimicking BS signal transmission in a cell be done?

11 December 2014 5,324 6 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View