How do we get the node information in RPL protocol using cooja simulator?

More Sankar Sennan's questions See All

How do we distinguish between power consumption and energy consumption in wireless sensor network?

How do we calculate the power consumption and energy consumption in wireless sensor network

04 May 2018 8,209 0 View

What is context aware Internet of Things? How can we adopt context in IoT architecture? Is context as middleware service for IoT application?

What is context aware Internet of Things? How can we adopt context in IoT architecture? Is context as middleware service for IoT?

03 April 2018 3,302 2 View

WSN nodes can we use in Internet of Things?

WSN nodes can we use in Internet of Things

11 December 2017 6,568 2 View

Can we do the cluster head selection using optimization technique for Internet of Things?

11 December 2017 3,801 3 View

Can anyone send me the code of Received signal strength calculation (RSSI) in cooja simulator?

Received signal strength calculation (RSSI) in cooja code

09 October 2017 1,218 1 View

What ways we can provide the efficient solution for energy efficient Routing for Internet of Things

What ways we can provide the efficient solution for energy efficient Routing for Internet of Things ?

05 June 2017 9,927 0 View

Which is the better tool for RPL routing in Low power and Lossy Networks

which is the better tool for RPL routing in Low power and Lossy Networks

05 June 2017 2,177 2 View

What is the beauty of RPL routing protocol in Internet of Things?

what is the beauty of RPL routing protocol in Internet of Things?

02 March 2017 8,353 4 View

Contiki Cooja not showing stats on Collect View?

Contiki Cooja not showing stats on Collect View

11 December 2016 1,165 0 View

What are the Research Challenges in IoT?

10 November 2016 4,831 2 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

Imed Romdhani

Hi,

Please refer to this tutorial:

https://www.researchgate.net/publication/304572240_Cooja_Simulator_Manual

Hope it answers your question.

Kind regards,

Imed

Technical Report Cooja Simulator Manual

Sankar Sennan

Hi Imed Romdhani,

You posted the document is very useful to me. Thank you.