How do I simulate the effects of drilling holes into a laminate in Midas NFX?

09 September 2017 0 8K Report

To check if the development of cracks on the blade root of a Wind Turbine is due to the drilling procedures during the manufacturing (glass-Epoxy laminate). Any help is appreciated.

Badges
Science topic

More Manoj Pradhan's questions See All

Any recommended software to calculate and check the bridge superstructure coordinates?

Japanese use JIP-LINER to calculate and check the Bridge Superstructure coordinates but it doesn't have an English version. Is there an English equivalent to the...

10 November 2018 5,827 0 View

What methods can be used for picking uniform points (to collect samples) in mountainous regions for mapping of engineering Soil parameters(in ArcGIS)?

We are using various krigging methods available in ArcGIS to map engineering soil parameters in mountainous region. Usually points with uniform distances picked by making grids are used in plane...

02 March 2015 6,265 2 View

Can index engineering soil parameters be related to any spectral data, digital elevation model or a satellite Imagery? Has anyone tried it out yet?

And is ArcGIS a good platform to carry out the project of determining Index soil parameters for an area?

08 September 2014 2,996 5 View

How does one classify Clay and Organic matter using Thermal Band of Landsat TM in ArcGIS ?

The thermal band of the Landsat TM has shown to be significant in contributing to the separability of soil categories through its ability to characterize the clay, organic matter, and iron-oxide...

07 August 2014 428 9 View

Can anyone kindly mail me Midas nfx 2016 English manuals, Mail ID: [email protected]?

These manuals get installed along with the software. I got the Japanese version of the manuals.

01 January 1970 7,047 0 View

Which is the most convenient manufacturing software for Additive Manufacturing?

Which tools can be used to generate machine codes for additive manufacturing?

02 March 2021 7,220 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View