How do we can show special parameter in visualization in the abaqus result like rupture index?

Hi I want to determine rupture index in ABAQUS but there is not exist this parameter in output result so i have to write special code for this. i do not know how i can write this code. i want to...

01 February 2018 1,112 2 View

How can we determine number of back stress in combined hardening?

how can we determine number of back stress in combined hardening in abaqus software? and what is back stress exactly? the number of back stress how effect on result ?

07 August 2017 8,065 2 View

How is slip rate calculated in abaqus ?

as slip rate is depend on slip velocity between the motion of surface, how can we use this in general static analysis ?

06 July 2017 5,063 0 View

How can i Import from ABAQUS/Standard to ABAQUS/Explicit?

05 June 2017 4,540 6 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Is SSRN e-Journal Scopus indexed?

I have publication in SSRN. I want to know whether it is Scopus indexed? Does it show impact factor? What is its ISSN No.?

02 March 2021 4,565 3 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View