Hello, I have a FORTRAN code which simulates heat transfer, I need to make it transient... Any help?
Thanks
Yes sir, I can send it to you by e-mail....Thanks!
Any help?
Hello dear Alvioli, I have sent you a message using researchgate...Thanks
How can I help you
Hello dear Oussama Rejeb thank you very much, I am no longer use FORTRAN because it does not have any interactive user interface, I use MATLAB and here is my tutorial :)...
Danke!
https://youtu.be/haDlzDCVxuw
Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...
08 September 2019 688 2 View
Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...
05 June 2019 8,078 4 View
Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!
05 June 2019 7,188 12 View
Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...
04 May 2019 6,100 3 View
Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks
04 May 2019 4,064 2 View
Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!
03 April 2019 2,799 6 View
Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks
02 March 2019 6,112 4 View
Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks
31 December 2018 5,908 5 View
Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!
31 December 2018 934 3 View
Hello, I have this UDF and it says that the airfoil changes the degree to +/- 8 through 1 sec, how is to work and how can we control the angle? /**********************************************/ /*...
09 October 2018 4,673 0 View
...
31 July 2024 1,671 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...
24 July 2024 367 4 View
I want to simulate WRF for a 12*12 km domain size. I want to run LSM and BSM models with a 5 minutes time interval. My laptop specification is 16GB RAM and Intel i5-1235U 1.3 GHz processor. Can I...
13 July 2024 2,037 0 View
Hi Dear All I would like to simulate a mode locked semiconductor laser. Does anyone know what is the best software to do it?
06 July 2024 1,648 4 View
I attempted to find a tutorial on YouTube but couldn't locate it. Could anyone guide me on how to view simulation results for Mobile Edge Computing using the OMNET++ simulator?
06 July 2024 6,229 0 View
I am looking at ways to investigate the biodegradation of 3D printed specimen as part of my research. To what extent can SimaPro be used to do this? The idea is to demonstrate the biodegradation...
02 July 2024 2,730 2 View
I used forcite module of Material Studio software to simulate the dissolution of zinc production waste in deep eutectic solvent. UFF force field has been used for the optimization of molecules,...
02 July 2024 7,494 1 View
I am trying to simulate a new solar cell which has almost 15 layers. But SCAPS has only 7 layers.
01 July 2024 9,135 2 View
Hello, Has anyone successfully modeled 2D argon plasma jet using the COMSOL? I would greatly appreciate any guidance on this matter.
30 June 2024 5,597 0 View