Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

Which is the best wavelength to study aerosol optical depth(AOD) related to climate reseach,which criteria must be adopted in choosing the wavelengh?

We are doing a study on impact of aerosol on precipitation. Which satellite data and which wavelength will be the best. or can some one suggest a criteria to be adopted to choose an instrument...

12 February 2021 6,324 3 View

How do we calculate 95% confidence intervals for RMSE?

I have two datasets (measured and modelled). I want to calculate 95% confidence intervals for RMSE. Cany anyone please help me with this? Thank you in advance

04 February 2021 5,439 6 View

Queries regarding the rain flow counting algorithm?

02 February 2021 9,790 2 View

Doubt in DFT geometry preparation?

Hi all, I am trying to perform some ab inito DFT calculations using cp2k code. I have a unit cell of 120 atoms and would like to know how to refine or reduce the number of atoms in the unit cell...

20 January 2021 6,024 3 View

Is it possible to ligate two restriction ends those have no complementary bases?

In my lab,we are trying to construct a control plasmid. So we have to remove the insert gene which has two restriction ends:one is XhoI and other one is Hind III.So after double digestion we want...

01 January 2021 3,271 4 View

Response Surface Methodology?

I'm using 3 different light intensities (constant values 15,30,45 W) for the wastewater treatment of an organic compound and optimizing the parameters (pH, catalyst dose and light intensity)...

31 December 2020 2,377 4 View

What is the impact of Pandemic on the higher education faculty?

Work life Balance, Stress, Anxiety, Effective teaching

28 December 2020 6,201 3 View

Why do we put a hyphen between nanocomposite?

compounds such as ZrO2 - SnO2 or ZrO2 - TiO2 etc.

01 December 2020 2,838 5 View

Can anyone please tell how to define link for Tuned mass Dampers using Sap2000/Etabs?

Dear Research scholars, I was doing my MTech thesis on pendulum based TMD and I was having trouble defining the link properties. I even followed the tutorials put on CSI website. still, I wasn't...

11 November 2020 8,309 11 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How could I process data in RCT to include it in meta-analysis?

I'm in the process of doing a meta-analysis and have encountered some problems with the RCT data. One of my outcom is muscle strength. In one study, I have three different measurements of muscle...

25 February 2021 7,603 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View