How to find out or construct(?) the right priors from data of previous experiment to use in a bayesian glm?

I have the following equation, Eating choice (Yes/No)~ Box type (A/B/C). So the question is whether a certain box type affects eating choice in groups of dogs. The eating choice of each member in...

10 February 2021 6,024 9 View

What are the ways to test the knowledge level of agricultural labourer about their day to day work?

what kind of test can I do for testing the level of knowledge about their daily operation?

03 February 2021 7,583 10 View

Why the bandgap of CH3NH3PbCl3 films are different for spin-coating method and electrospinning method?

The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?

08 January 2021 5,646 6 View

Why monoethanol amine is used as flocculant?

I want to know the reaction mechanism of monoethanol amine used as flocculating agent for rerefining used lubricating oil. Here I have attached one research paper where MEA (monoethanolamine) is...

01 January 2021 5,681 2 View

Problem with GST-fusion protein elution- Can anyone help?

18 December 2020 4,559 6 View

How can I determine metal concentration of Used lubricating oil by AAS?

I am a junior research fellow in the department of Chemical Engineering, Nit Durgapur. I want to know that how can I determine various metal such as Fe, Cr, Mg, Mn, Pb concentration present in...

15 December 2020 9,887 3 View

Regarding the O 1s XPS pf phyllosilciates, the peak near 531 belongs to Oxygen vacancy sites or O bonded to the Si from the silicate tetrahedra?

In O 1s spectra, usually the peak near 531 eV belongs to oxygen vacancy sites in oxides, however, in silicates, these peaks are often reported to originate from O-Si. I am confused if the intense...

10 December 2020 9,496 2 View

What is the mol. weight of GFP-11 tag?

Hi, I am trying to find out the mol. weight of GFP 11 because it is tagged to my protein of interest which is 17kDa. GFP 11 has been tagged with my protein of interest while GFP 1-10 is tagged...

09 December 2020 1,863 1 View

How to PEGylate Fluorescntl Polystyrene Particle?

I have Fluorescent Polystyrene beads. I need to graft PEG on the surface of it. I am looking for a protocol to do that. Also need to know which experiment to perform to be sure about the grating.

01 December 2020 7,860 1 View

How to control for categorical independent variables (e.g., education) when doing regression discontinuity using STATA?

I am conducting a regression discontinuity design where the dependent variable is continuous while control variables are categorical (except the treatment variable). In the usual regression...

01 December 2020 583 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View