How can imply immersed boundary Lattice Boltzmann Method?

More Reza Bahoosh's questions See All

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How to solve the fatal error "the entire source was rejected" in MCNP?

Simple geometry was made having concentric cylinders bounded by a square region. The geometry has a reflective boundary. The source was defined at one point in the boundary and when it had been...

17 February 2021 4,364 3 View

How does a freeze dryer destruct your solid sample?

Several times I lost my sample during freeze drying. There was no solid or powder in the vial after freeze drying. I'm sure sample contained solute because i took its NMR spectrum. I covered the...

15 February 2021 6,749 2 View

How to model Type 1 collagen structure for finite element analysis ?

I have started a project in which stress distribution in Type 1-collagen scaffold is to be modelled. I am thinking of using finite element analysis to model the structure and the loading...

07 February 2021 5,487 3 View

Hey guys, I'm looking for an efficient protocol to transfect patient-derived tumor cells with a high rate of transient transfection?

As you know it's quite tricky to get primary cells transfected at a relatively high rate!

31 January 2021 3,580 4 View

How can I model a vacuum region between a concentric tube in Ansys fluent?

I am modeling a double pipe (concentric tube) in Ansys Fluent. The center tube contains nanofluid, and the region between the pipes is a vacuum zone. The outer tube is used for reducing convection...

22 January 2021 2,781 3 View

What type of plants is better to work in gene regulation control project ?

I Interested in to work in gene network modeling thus I need to know what is future of gene network modeling in agriculture thanks

04 January 2021 6,527 3 View

Is it possible to culture several cell lines in the same plate/dish/flask with complete cell separation?

I'm trying to screen the effect of a toxic agent. I need to see its effect on a few different cell lines with different degrees of resistance to this compound. I would like to possibly culture...

31 December 2020 5,740 3 View

Help with insect identification?

Could someone help me identify the insect in this picture?

31 December 2020 2,109 5 View

How to find the natural frequency of nonlinear model (hyperelastic materials) in ansys APDL?

I'm working on the FE analysis of nonlinear vibration of circular plate in ansys APDL. I considered the Mooney-Rivlin model of hyperelastic materials. So i want to know that how to find natural...

27 December 2020 8,696 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Amir Alimoradi

Hello Reza

I am writing a code for IB-LBM too.

You should read this book. It is perfect.

Book The Lattice Boltzmann Method - Principles and Practice

Reza Bahoosh

Anastasiia and Amir Thanks

Arnab Ghosh

To get a comprehensive idea regarding the development of your own immersed boundary lattice boltzmann code from scratch for both stationary and moving boundary cases, you can refer to my thesis available in my profile.