Why some engineers design inductors to generate an uniform magnetic field by means of two separated parts?

08 September 2017 7,621 0 View

How can I provide a high power inductor winding under following conditions?

08 September 2017 920 5 View

How can I stop a DC motor which operate in 6000rpm speed at a second?

I want to stop a 100W DC motor when it works at 6000rpm and its mechanical torque is 0.1N.m. Can I stop it at a moment (fast stop) by means of the four quadrant converter? Or I have to use a...

31 December 2016 8,785 11 View

Any advice in using Honeywell current sensor CSNE151 model?

I want to use CSNE151 current sensor in my control loop. Output of this device goes to the microprocessor then i have to decrease this output to 3 volt. i can't find suitable circuit model to...

11 December 2015 1,295 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View